Question 10: A water heater is supplied with cold water (T-30-F) and delivers hot water at a thermostat setting at T₂=130 F. Assume the heat lost to the surrounding is 400 Btu/hr. What is the heating rate to supply water at a rate of 10 gallons/hour? Assume the heat storage 4H, = 0. [1 gallon of water = 8.3 lb-m, 1 kWh =3413 Btu, Specific heat capacity of water C₂ = 1 Bulb-F]

Question 10: A water heater is supplied with cold water (T-30-F) and delivers hot water at a thermostat setting at T₂=130 F. Assume the heat lost to the surrounding is 400 Btu/hr. What is the heating rate to supply water at a rate of 10 gallons/hour? Assume the heat storage 4H, = 0. [1 gallon of water = 8.3 lb-m, 1 kWh =3413 Btu, Specific heat capacity of water C₂ = 1 Bulb-F]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A domestic refrigerator sits in a kitchen, switched on, with the refrigerator door wide open. The kitchen itself is well insulated and it can be assumed no heat can escape or enter the kitchen from the outside. Which of the following is the most accurate statement. а. The temperature in the kitchen will stay the same. O b. The temperature in the kitchen could go up or down depending on the mechanical efficiency of the compressor. O c. The temperature in the kitchen will go down very slightly. d. The temperature in the kitchen could go up or down, depending on the Coefficient of Performance (COP) of the refrigerator. е. The temperature in the kitchen will go up very slightly.
| Part of a refrigeration system operates at steady state with Refrigerant 22 as shown in the figure below. There is no significant heat transfer to or from the heat exchanger, valve, and piping. Kinetic and potential energy effects are negligible. State 1 is a saturated liquid. What temperature is it, in °F? Describe the refrigerant at state 4 as one of the following: compressed liquid, saturated liquid, tyro-phase mixture, saturated vapor, or superheated vapor. Determine the required mass flow for the given operating conditions, in lb/min. Determine the rate of heat transfer between the evaporator and its surroundings, in b. Btu/min. Make sure to clearly state the direction of heat transfer. 1. T=10°F P= 15 Ibf in (AV), = 9.5 ft/min. Pi= 120 Ibf/in.? Heat exchanger Throttling valve Evaporator P 15 lbfin.2 X3 = 1.0 P2= 15 lbf/in.2
A refrigeration unit with COP = 3.8 is being used to remove heat from a particular machine by 0.42 kg/s of water (C, = 4.18 kJ/kg.K) at 20 °C that is chilled from 40 °C as shown in the Figure. What is the power input (in kW) to the refrigeration unit? Select one: O 11.15 1 2 10.97 9.24 REF TH O 13.26 QH O 14.63 O 12.32
A reversible refrigeration cycle operates between cold and hot reservoirs at temperatures Tc and TH, respectively. (a) If the coefficient of performance is 10 and Tc = -40°F, determine TH, in °F. (b) If Tc = 0°C and TH = 30°C, determine the coefficient of performance. (c) If Qc = 500 Btu, QH=600 Btu, and Tc = 20°F, determine TH, in °F. (d) If Tc = 50°F and TH = 100°F, determine the coefficient of performance. (e) If the coefficient of performance is 5.5 and Tc = -5°C, find TH, in °C. Part A If the coefficient of performance is 10 and Tc = -40°F, determine TH, in °F. TH= i Save for Later °F Attempts: 0 of 4 used Submit Answer
Thermo review I cannot solve the last part of this question- thank you! A heat engine with a thermal efficiency of 45% rejects 1000 kJ/kg of heat to a low temperature sink. d) A Carnot heat pump operates between 273 K and 313 K, determine its Coefficient of Performance.
4. The values of a vapor compression refrigeration cycle were given below. Calculate the values of refrigerant flow rate, refrigeration capacity, and the COP of the system. T1= Evaporator water outlet = 10 °C T2= Evaporator water inlet = 16 °C T3= Condenser water inlet = 16 °C T4= Condenser water outlet = 22°C Cooling water flow rate = 1.5 L/min Heating water flow rate = 1.5 L/min Enthalpy of R134a in evaporator outlet = 305 kj/kg, Enthalpy of R134a in evaporator inlet =115 kj/kg Enthalpy of R134a in condenser inlet =327 kj/kg
Required information Refrigerant-134a enters the condenser of a steady-flow Carnot refrigerator as a saturated vapor at 65.0 psia, and it leaves with a quality of 0.05. The heat absorption from the refrigerated space takes place at a pressure of 30 psia. Determine the coefficient of performance. (Round the final answer to three decimal places.) The coefficient of performance is
Roughly how many tons of cooling does it take to cool a space where the following equipment is stored but no people? The equipment is running continuously: 3 refrigerators - capacity, 3000 Watts each; 10 Fluorescent lights - 64 Watts each; Two copy machines - 1000 Watts each a. 3.5 tons, b. 10 tons, c. 1 ton, d. 0 tons, there is no need to cool equipment.
14. During the summer the temperature inside a van reaches 130 F while the outside temperature is a constant 95 F. When the driver gets into the van, she turns on the air conditioner with the thermostat set at 60F If the time constant for the van is 1/K, = hr, when will the temperature inside the van reach 80 F?
A reversible refrigeration cycle operates between cold and hot reservoirs at temperatures Tc and TH, respectively. (a) If the coefficient of performance is 3.5 and Tc = -40°F, determine TH, in °F. (b) If Tc = 0°C and TH = 30°C, determine the coefficient of performance. (c) If Qc = 500 Btu, QH = 600 Btu, and Tc = 20°F, determine TH, in °F. (d) If Tc = 30°F and TH = 100°F, determine the coefficient of performance. (e) If the coefficient of performance is 2 and Tc = -5°C, find TH, in °C.
The values of a vapor compression refrigeration cycle were given below. Calculate the values ofrefrigerant flow rate, refrigeration capacity, and the COP of the system.T1= Evaporator water outlet = 10 °CT2= Evaporator water inlet = 16 °CT3= Condenser water inlet = 16 °CT4= Condenser water outlet = 22°CCooling water flow rate = 1.5 L/minHeating water flow rate = 1.5 L/minEnthalpy of R134a in evaporator outlet = 305 kj/kg,Enthalpy of R134a in evaporator inlet =115 kj/kgEnthalpy of R134a in condenser inlet =327 kj/kg
Homework: A counterflow heat exchanger is located between a collector and a storage tank. The fluid in the collector side is a water-glycol mixture with cp=3840 J/kg. °C and a flow rate of 1.35 kg/s, whereas the fluid in the tank side is water with a flow rate of 0.95 kg/s. If the UA of the heat exchanger is 5650 W/°C, the hot glycol enters the heat exchanger at 59°C, and the water from the tank at 39°C, a) estimate the heat exchange rate; b) if FRUL is 5.71 W/m².°C and collector area is 16 m², what is the ratio FR/FR?