Question 1.11 A beam has a rectangular cross section and is subjected to a shear force V along the negative y direction, as shown in Figure Q1.11. Points A and B are located at the centre and bottom surface of the cross section. What is the correct statement? t B Figure Ql.11 O a. The minimum shear stress induced by the shear force is located at Point B and its value is zero. O b. The minimum shear stress induced by the shear force is located at Point B and its value is non-zero. O c. The minimum shear stress induced by the shear force is located at Point A and its value is non-zero. O d. The minimum shear stress induced by the shear force is located at Point A and its value is zero.

Question 1.11 A beam has a rectangular cross section and is subjected to a shear force V along the negative y direction, as shown in Figure Q1.11. Points A and B are located at the centre and bottom surface of the cross section. What is the correct statement? t B Figure Ql.11 O a. The minimum shear stress induced by the shear force is located at Point B and its value is zero. O b. The minimum shear stress induced by the shear force is located at Point B and its value is non-zero. O c. The minimum shear stress induced by the shear force is located at Point A and its value is non-zero. O d. The minimum shear stress induced by the shear force is located at Point A and its value is zero.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SHOW SOLUTION AND ILLUSTRATION
The following stress element represents the stress state at point A of the structure in the figure below. Determine the maximum shear stress in this condition. 52.8 MPa 26.4 MPa O a. 32.78 MPa O b. 29.65 MPa Oc. 40.25 MPa O d. 37.34 MPa
Tb = 80.51
A square post with a tubular cross section is loaded as shown in the figure below. a) Determine the state of the stress at point A having sides parallel to x and y axes. b) Determine the principal planes and principal stresses at point A at the base of the post.
B6
A beam has a cross-section as shown in Figure Q5. The beam is subjected to a vertical shearing force of 100KN through the shear centre. For the system: a) determine the second moment of area about the x - x plane and b) determine the shear stress distribution along the y – y plane, c) plot the shear stress distribution on a suitable graph, labelling the principal values. y! Centre of Gravity. y' 30 тm 60 тm шш 09 120 тт
A thin beam with a solid rectangular cross-section is loaded as shown in Figure Q7 below. W W L/3 L/3 L/3 Figure Q7 What is the ratio of the maximum to nominal shear stress for the beam described in Question 7? O a. 3:2 O b. 1:4 Ос. 3:1 O d.2:1 O e. 1:2 O f. None of the provided answers are correct. O 8. 1:1
len 2
The stresses shown in the figure act at a point on the free surface of a machine component. If o = 22.4 ksi in the direction shown, determine the shear stress Txy at the point. Txy O 14.48 ksi 11.51 ksi O 13.53 ksi O 10.63 ksi O 8.84 ksi 5.0 ksi 24° 2.8 ksi
1. For the beam showing in the figure, consider section n-n and determine; (a) The largest shearing stress in that section (b) The shearing stress at point a. 0.3 m 40 nim 10 KN 12 imm 150 mm 12 mm 200 mm 15 in
ضحهقهصكسنتلوؤزذ