The state of stress at a point is shown on the element.(Figure 1)Figure12 ksi1 of 130 ksiPart BDetermine the orientation of principal planes of stress.Enter your answers in degrees to three significant figures separated by a comma.IVE ΑΣΦ | 11 | vec0,0,19.33,109.33Submit Previous Answers Request Answer* Incorrect; Try Again; 2 attempts remainingPart C?Determine the maximum in-plane shear stress.Express your answer in kilopounds per square inch to three significant figures.Tmax in-plane 19.2 ksi

Answered: Image /qna-images/answer/817a39c3-0569-45d7-be8a-7dcb61762138.jpg

Determine the orientation of principal planes of stress. Enter your answers in degrees to three significant figures separated by a comma. Opp, 19.33,109.33 Submit IVE 1971 ΑΣΦ. It Ivec ▾ Part C Previous Answers Request Answer * Incorrect; Try Again: 2 attempts remaining Tmax in-plane Determine the maximum in-plane shear stress. Express your answer in kilopounds per square inch to three significant figures. ? = 19.2 ksi

Determine the orientation of principal planes of stress. Enter your answers in degrees to three significant figures separated by a comma. Opp, 19.33,109.33 Submit IVE 1971 ΑΣΦ. It Ivec ▾ Part C Previous Answers Request Answer * Incorrect; Try Again: 2 attempts remaining Tmax in-plane Determine the maximum in-plane shear stress. Express your answer in kilopounds per square inch to three significant figures. ? = 19.2 ksi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 6.77 The pin, attached to member BCD, passes through a smooth slot in member AB. (Figure 1) Take t=240 lb/ft. Figure 48 1 of 1 Y 4 Part A A.. A,- 72,95 Determine the components of the reaction at support A Express your answers in pounds to three significant figures. Enter your answers separated by a comma. 195] ΑΣΦ. 11 Ivec Submit X Incorrect; Try Again Part B. Previous Answers Request Answer Determine the reaction af support C. Express your answer in pounds to three significant figures. VAX i vec C₂-288 ? lb P 7 of 7 Ib Review
The truss is a preliminary design for a structure to attach one end of a stretcher to a rescue helicopter. Based on dynamic simulations, the design engineer estimates that the downward forces the stretcher will exert will be no greater than 1.6 kN at A and at B. Figure 300 mm T 290 mm D B F Search 390 mm C A 150 mm 480 mm 200 mm 1 of 1 Prov
the steps please
5 12.42
Determine the magnitude of moment (Nm) of the 773-N force about point A if x = 0.43 m , y = 0.74 m, and θ = 48.1ᵒ. Round off only on the final answer expressed in 3 decimals. Instead of units, type either POSITIVE or NEGATIVE to indicate the direction of moment which is consistent with the sign convention discussed on lectures. Sample answers are 12.908 POSITIVE or 12.908 NEGATIVE.
Q3 / An element in plane stress at the surface of a large machine is subjected to stresses shown below. Using Mohr's circle determine the following quantities (a) the principal stresses and their directions and (b) the maximum shearing stresses and the directions of the planes on which they occur. 103.425MPA 55.16MPA 82.74MPA 82.74MPA 55.16MPA 103.425MPA
3. The damped motion of a vibrating particle is defined by the position r = x1 1-i+(y,ecos2pt )j , where t is in seconds. For x1 = 30 mm and yı = 30 mm, determine the position, velocity and acceleration of particle at time t = 0 s and t= 1.5 s yly | 1.0 0.5 0.2 0.4 0.6 xlx, -0.5 -1.0 212
Hand written please .
Help!!! Answer all correctly
Help!!! Answer all correctly
Urgent , looking for right answer.
i need the answer quickly