Question 1 Calculate the osmotic pressure (n) at 50 C of a glucose solution C6H1206 that has 60 g of glucose dissolved in enough water to make 1500 mL? (atomic masses: C: 12; H: 1;0:16 Answer: T = ] atm tinn will save tnis response

Q: Researchers studied the electronic properties of a one-dimensional chain sulfur by encapsulating S…

A: Given :Atomic radius of sulphur C-C bond length Surface energy

Q: Estimate the concentration of ethylbenzene in fish tissue in a lake with a concentration in water of…

A: Ethylbenzene concentration in water = 120 mg/L

Q: The figure below shows the soybean oil production process. In the  Soybean oil production is used…

A: Given that

Q: In the situations described below, what is the free energy change if 1 mole of Na* is transported…

A: Given that: Moles of Na+ transported = 1 mol Intracellular concentration of the region 1 = 1μM =…

Q: The marketing slogan 'consumes 47 times its weight in excess stomach acid solution' has long been…

A:

Q: 3. The kinetics of the acid-catalyzed hydrolysis of the SerVal peptide were studied in methanol,…

A:

Q: The concentration of pentachlorophenol (C6HCl5O) has been measured to be 42.8 μg/L in Lake Pekko. A…

A: The ratio of a chemical's concentration in an organism to that of its surroundings is known as the…

Q: A packed tower is designed to remove component A from an aqueous stream into a countercurrent air…

A: a) The individual gas film coefficient  b) The interfacial gas concentrationc) The individual liquid…

Q: The sedimentation rate of red blood cells (RBC's) in blood diluted with water and anticoagulant is…

A: Introduction The sedimentation rate is a blood check that examines inflammation in your body. It’s…

Q: Reconsider Prob. 14–54. Using EES (or other) software, plot the highest rate of hydrogen loss as a…

A: Given data: Thickness of the pipe = 1 cm Inner Diameter of pipe = 3 m Pressure = 500 kPa Mole…

Q: 4. Adsorption isotherm (Freundlich isotherm) of powdered activated carbon (PAC) using for removing…

A:

Q: ypically one would use a non-reactive substance such as smoke or sulfur hexafluoride is used to…

A: To determine  the slope of a plot of concentration vs time

Q: Q.1) In an air-CO2 mixture at 298k & 303.9 KN/m², the concentration of CO2 at two planes (2mm) apart…

A:

Q: Effluent from a biological process is treated using activated carbon and allowed to come to…

A: The concentration versus the adsorbed solute is given.

Q: calculate the percent of the total of all cyanic acid species in solution which are ionized in a…

A:

Q: Experiments are conducted on the uptake of a water pollutant in water over an adsorbing solid. Once…

A: Given: Pollutant is adsorbed over solid  After reaching equilibrium the concentration of pollutant…

Q: Three fixed-bed adsorbers containing 10,000 lb of granules of activated carbon (ρb =30 lb/ft3 ) each…

A: Given information:   3 fixed-bed adsorbers Mass of activated carbon granules in each bed, m =…

Q: Carbon tetrachloride (CC14) is diffusing through benzene (C6H6), as the drawing illustrates. The…

A: Cross sectional area A = 3×10-4 m2 CL = 1.85×10-2 kg/ m3 Mass flow rate m/t = 4.29×10-13 kg/s…

Q: Tsuge and Matsuo studied precipitation of Mg(OH)2 by reacting aqueous solutions of MgCl2 and Ca(OH)2…

A: Magnesium hydroxide is precipitated by reacting of aqueous solution of MgCl2 and Ca(OH)2 in a 1-L…

Hazard Analysis and Design in Chemical Engineering

Hazard is the intrinsic property of a material or process which harms the people, buildings, or environment. Health, safety, hazard, risk assessment, loss prevention, and environmental consideration play an important role while designing a chemical processing plant. Hazard is often confused with risk. Risk measures the magnitude of loss and injury of likelihood incidents or the consequence and frequency of incidents.