QI. A 200 V de shunt motor has R. 1N and Ra 200 2. When running on No-load the current taken is 5A and the speed is 1000rpm. Calculate: (i) The speed when motor is fully loaded and the total current drawn from the supply is 40A. (ii) Explain what will happened to the speed when fully loaded and the shunt field current is reduced by 10%.

QI. A 200 V de shunt motor has R. 1N and Ra 200 2. When running on No-load the current taken is 5A and the speed is 1000rpm. Calculate: (i) The speed when motor is fully loaded and the total current drawn from the supply is 40A. (ii) Explain what will happened to the speed when fully loaded and the shunt field current is reduced by 10%.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The shunt field resistance of a 200 V shunt motor is 150 ohms and its armature resistance is one-tenth of an ohm. Determine the efficiency of the motor at full load if the current on the line is 120 A at 200 V. The line current of the motor is five amperes during no-load condition. List the assumptions made if any.
A 400 V series motor has a field resistance of 0.02 ohm and an armatureresistance of 0.1 ohm. The motor takes 30 A of current at 1000 rpm whiledeveloping full load torque. What is the motor speed when this motordevelops 60 % of full load torque and the shunt is shunted by a resistorof 0.03 ohm? [Ans. 1294.98 rpm]
Hello Could I please get a step by step explanation with answer Thank you
Qa/ a- Explain the difference in the Torque-Speed Characteristics of DC Shunt and series Motors. b+ A 120 V shunt motor has the following parameters: Ra = 0.4 0, RF = 120 Q. On full load, the tine current is 19.5 A and the motor runs at 1200 rpm, find the output torque.
Question4 A 120-V series motor runs at 2000 rpm at full load and takes a current of 12A. The armature resistance is 0.3 ohms and the series field resistance is 0.2 ohms. A diverter resistance of 0.2 ohms is connected across the series field, and the load on the motor is adjusted. If the motor now takes 20A, what is the new speed of the motor, determine the torque developed in each case.
Final 1A DC shunt motor is rated 10HP, 250V and is connected to 235V source. The armature resistance is 0.2 ohm, the field circuit resistance is 125 ohm and the total rotational losses are 380W. The motor is driving a load, and it draws an armature current of 30A, Calculate the output power. b) 41 d) 6490 6870 7492 7460 Boş birak
Question The power input to a 500 V, 50 Hz, 6-pole, 3-phase induction motor running at 975 RPM is 40 kW. The total stator losses are 1 kW. If the total friction and windage losses are 2.025 kW, then the efficiency is %
A 2 hp 50 Hz 3-phase 220 V delta wired induction motor has a full-load rated speed of 1400 rpm. a) How many poles does the motor have? b) Calculate its rated output torque. c) What is the slip at full load? d) If the current is 6.37 A with a power factor of 0.79 at full load, what is the efficiency of the motor? e) Calculate the torque and approximate speed at ½ load. f) If a variable frequency drive were used to control the speed of this motor, what is the approximate maximum speed for the load from e)? What frequency would the drive be set to? Please answer all subpart either dislike is ready please all subpart in short please
The current drawn by the 230 V DC motor of armature resistance 0.5 ohm and back emf 200 V is ?
A 550-volt long-shunt compound motor has armature an resistance of 0.815 ohm and a series field resistance of 0.15 ohm. The full load speed is 1,900 rpm when the armature current is 22 amp. (a) At what speed will the motor operate at no load if the armature current drops to 3 amp with a corresponding drop in flux to 88 per cent of the full-load value? (Assume a brush drop of 5 volts at full load and 2 volts at no load.) (b) Calculate the percent speed regulation of the motor.
Q1. а. The dc motor with the shunt connection has the following parameters: Voltage terminal, VT = 240 V Line current, IL = 100 A Armature resistance, RA = 0.14 Q Field resistance, RF = 200 Q Adjustable resistance, Radj = 0 to 300 Q No load speed, no = 1200 rpm The internal generated voltage Ea and field current characteristics graph is shown in FIGURE Q1. 300 Speed = 1200 rimin 250 200 150 100 50 0.0 0.25 0.5 0.75 1.00 1.25 1.50 Field Current, A FIGURE Q1 i. Calculate the no-load speed of this motor when Radj = 120 Q. ii. Calculate the full-load speed when the motor Radj = 120 Q. ii. Under no-load conditions, determine the range of possible speeds can be achieved by adjusting Radj? Internal generated voltage E, V
A 400v series motor working with unsaturated field is taking 60 A and running at 840 rpm. The total resistance of the motor is 0.1 ohm. At what speed will the motor run when developing half-full load torque.