A DC compound motor has shunt field resistance of 5002 and series field resistance of 22. Shunt field current is 0.44A. Armature is lap wound with 200 conductors running at 600rpm. Flux per pole is 0.1Wb. Armature winding resistance is 0.12 and it is dissipating 10W. Other losses amount to 35W. Calculate the efficiency of the motor.

Q: . Explain the reasons for the low power factor in the power system network. 2. Discuss any two…

A: We need to explain the reasons for the low power factor in the power system network.

Q: What is mean by equipment grounding and system grounding?

A: As per bartleby guideline for more than one question asked only first three are to be answered…

Q: After reduction, the current - caring capacity of a condenser is referred to as the___. A. ambience…

A: Given: After reduction, the current carrying capacity of a conductor is referred to as the ___.

Q: List the minimum trade size Type EMT for each of the following applications. (Objective 12-1)…

A: As per Bartleby expert policy only first individual question is to be answered. So, answering only…

Q: Briefly describe the major difference between HEC and CLP regarding the connection from the…

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: g Technology- Toronto CHAPTER 7: SOLDERING TECHNIOUES ES 7.5 QUESTIONS Which tools will you need for…

A: Note: According to bartleby guidelines, we have to answer only first question. 1) Soldering is the…

Q: Explain briefly, the Professional Code of Ethics of an Electrical Engineer.

A:

Q: What justifies the need for plenumrated cabling above the ceiling tile?

A:

Q: Clear print on the keyboard and correct or dislike  In regards to the model of a real transformer,…

A: Transformer is an ac static electrical device that transfers electrical energy from one electrical…

Q: How does IoT fit into the concept of the "smart grid" in energy distribution

A: We need to explain How  IoT fit into the concept of the smart grid in energy distribution.

Q: What are the three project categories an electrical contractor may choose to browse?

A: There are different projects in the world, and every project needs some specialty for completing it.…

Q: Cần be driven by a single digital 1C output is a characteristic called a) low power dissipation. c)…

A: 2. The number of parallel loads that can be driven by the single digital IC output is a…

Q: These transformers normally mounted on power poles or installed inside a large building near…

A: 1) Transformer is an electrical machine which step up step down the voltage without change in…

Q: A transformer secondary provides 35 Vrms to a full wave voltage-doubler circuit. The dc output…

A:

Q: What is UPS in electrical engineering?

A: Full form of UPSUninterruptible power supply

Q: TTR 300 , What is the method of connecting the device to the transformer ?

A:

Q: * Experiment No3:- Loaded operation of the Dc Series Gen-erater H.W.:- who is the Best shunt or…

A:

Q: As an electrical and electronic engineer, your manager has asked you to write a report for the…

A: Report: Electrical Safety Devices for Induction Motor Applications Date: [Current Date]To: New…

Q: Training is required for: Qualified electricians only. b. Only those workers who work on or near…

A: Bartleby has policy to solve only first question and incase if it has subparts then solve only first…

Q: Name two nationally recognised electrical testing laboratories in the United States.

A: In the following section, two nationally recognized electrical testing laboratories present in the…

Q: Two identical (in terms of voltage and power ratings) transformers A & B are designed to ru at…

A: In this question,  We need to choose the correct option We know Weight of the transformer is…

Q: What are the basic/necessary steps to design a pico hydro power plant? Inlcude the parts of…

A: The basic/necessary steps to design a pico hydropower plant: • It should be practical and suitable,…

Q: Power transformers are not used by. . a. Residential buildings b. Industrial plants c. Electric…

A: Power transformer are used where high amount of power is used by single service or customer like 50…

Q: What is the mean of wiring

A: Wiring is the term used for the supply system design, connection, and protection schemes employed…

Q: Explain the concept of load shedding and provide examples of situations where load shedding might be…

A: Load shedding is a controlled and intentional reduction of electrical power supply to specific areas…

Q: Draw the block diagram representation of a heating system.

A: Answer- Block diagram of heating system -

Q: 1. Outline/Give Two examples for job factors that could lead to poor/bad health and safety behaviour…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: 3 phase fully controlled rectifier has a 3 phase line to line supply voltage of 410 V rms at 50 Hz…

A: A full-wave rectifier is AC to DC converter. A three-phase fully controlled rectifier converts AC…

Q: (i) The full-load current, (ii) The full-load copper losses, (iii)The full-load efficiency, (iv)The…

A: The DC shunt generator has,  Terminal voltage Vt=450 V Armeture resistance Ra=0.75 ohm Shunt field…

Q: power transmission based on the given function.

A: Transformer- A device that transfers the electrical energy between two electrical circuits which are…

Q: 7. What are insulation requirements for high-voltage Air or SF6 circuit breakers?

A: Insulation  requirements  for high voltage air or sf6 circuit breakers :  The insulation of the…

Q: Draw the circuit diagram of Two quadrant chopper which is having average load current might be…

A: Chopper: Chopper is a device which transfers the dc power from one circuit to another circuit. Two…

Q: How does IoT technology contribute to optimizing energy consumption in residential buildings and…

A: How does IoT technology contribute to optimizing energy consumption in residential buildings and…

Q: Discuss the significance of back emf in a dc motor. Note: Figures and sketches are required.

A: Back e.m.fWhen armature of the dc motor rotates, then the conductors or the windings on a armature…

Q: What justifies the need for plenumrated cabling above the ceiling tile?

A: ANSWER                            There are several reasons why we use…

Q: Explain any three factors which affect the efficiency of a wind turbine

A: In this answer let us try to understand the three main factors that are affecting the efficiency of…

Q: DETERMINE IF THE STATEMENT/IMAGE IS FOR : DELTA- DELTA or WYE- WYE (follow the writing and spelling…

A: Transformer connection Three forms of connection are possible in three-phase transformer windings.…

Q: Discuss in detail about the role of SVC in improving the stability limit and enhancing the power…

A: Discuss in detail about the role of SVC in improving the stability limit and enhancing the power…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.