QI: A steel cantilever beam, as shown in Fig, is subjected to axial load varies from 110 N (compression) to 450 N (tension). Determine the required diameter at the change of section for infinite life using a factor of safety of 2. The strength properties are as follows: Ultimate strength = 550 MPa Yield strength = 470 MPa Endurance limit = 275 MPa 110 N 450 N 2d 0.2d

QI: A steel cantilever beam, as shown in Fig, is subjected to axial load varies from 110 N (compression) to 450 N (tension). Determine the required diameter at the change of section for infinite life using a factor of safety of 2. The strength properties are as follows: Ultimate strength = 550 MPa Yield strength = 470 MPa Endurance limit = 275 MPa 110 N 450 N 2d 0.2d

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A composite assembly consisting of a steel [G = 80 GPa] core (2) connected by rigid plates at the ends of an aluminum [G = 28 GPa] tube (1) is shown. The cross-sectional dimensions of the assembly are shown in the second figure. Assume L = 340 mm, D1 = 53, d = 37 mm, d2 = 19 mm. If a torque of T = 1200 N-m is applied to the composite assembly, determine (a) the maximum shear stress in the aluminum tube and in the steel core. (b) the rotation angle of end B relative to end A. (1) T T B L (1) d2 di DI Answers: (a) Talum = i 53.839 MPa Tsteel i 891.026 MPa (b) PB - PA = i 0.02467 rad (2)
The composite bar shown in the figure is firmly attached to unyielding supports. An Axial force P = 52 kips is applied at 65°F. Compute the stress (ksi) in the Aluminum at 116 °F. Assume a = 6.5 x 10-6/° F for steel and 12.8 x 106/°F for aluminum Given: L1 = 15in; L2 = 11in Your final answer should contain two decimal places Steel A = 3 in² E = 29 x 106 psi Correct Answer: 3.92 L2 Aluminum A = 2 in² E = 10 x 106 psi L1
The following structure has a compression allowable stress of 50 MPa. In the laboratory, it was found that the allowable stress in tension is 5 MPa.
QI/ An aluminum bar carries the axial loads at the positions shown in Fig. 1, below. The diameter for part AB, BC and CD is 35 mm, 40 mm and 30 mm, respectively. The elastic modulus for aluminum is 72.4 x 10 N/mm. Determine the internal stresses at section (A-B), (B-C) and (C- D), and the elongation (AL) in length at each part of aluminum due to loading. в D 37 kN 10 kN 45 kN 18 kN 1000 mm 800 mm I 600 mm Fig. 1
A cylindrical specimen of some metal alloy having an elastic modulus of 101 GPa and an original cross-sectional diameter of 3.6 mm will experience only elastic deformation when a tensile load of 2430 N is applied. Calculate the maximum length of the specimen before deformation if the maximum allowable elongation is 0.41 mm. i mm
PLEASE WRITE YOUR COMPLETE SOLUTION AND BOX THE FINAL ANSWER. THANK YOU. A series of rigidly attached aluminum bars carries the axial loads at the positions shown. If the modulus of elasticity E = 16×10^6 psi, compute the total deformation of the bar and state if the bar elongates or shortens. Assume that the bar is suitably braced to prevent lateral buckling.
Two T-shape sections are welded together to create a composite l-beam section as shown below. Determine the safely uniform load w (kN/m) that the beam can carry throughout its entire span. 270mm 30mm 20mm 160mm Welded Joint 130mm 30mm 135mm Beam Length = 4 m Consider the following stresses: fb(T) 3 125 МPа fb(C) = 130 MPa x at the welded joint = 20 MPa Find: 1. The Neutral Axis from the base 2. moment of inertia with respect to the horizontal centroidal axis 3. Q at the welded joint 4. Considering the maximum flexural stress in tension, WNAX is equal to KN/m. 5. Considering the maximum flexural stress in compression, WMAX, is equal to 6. Considering the stress at the welded joint, wMex is equal to kN/m.
Please help
A cantilever beam with cross section shown below and span of 3 m is subjected to concentrated load (P) at the free end. If the maximum allowable tensile stress equals to 10 MPa what is the maximum value of the load P can be applied.
Determine the y-bar centroid of the composite figure shown. Where: x=4 ft 2 A 1 ft 1ft
Need answer