Q9: The reactance data for the power system shown in Figure below in per unit on a common base is as follows: T1 Т 3 1 4 ojo G1 G2 X1=X;= 0.3 Xo=0.5 X,=X,=0.1 X=0.25 X=0.25 X,=X,=0.1 Хо-0.05 Xo=0.05 Obtain the Th'evenin sequence impedances for the fault at bus 1 and compute the fault current in per unit for the following faults: (a) A bolted three-phase fault at bus 1. (b) A bolted single line-to-ground fault at bus 1. (c) A bolted line-to-line fault at bus 1.

Q9: The reactance data for the power system shown in Figure below in per unit on a common base is as follows: T1 Т 3 1 4 ojo G1 G2 X1=X;= 0.3 Xo=0.5 X,=X,=0.1 X=0.25 X=0.25 X,=X,=0.1 Хо-0.05 Xo=0.05 Obtain the Th'evenin sequence impedances for the fault at bus 1 and compute the fault current in per unit for the following faults: (a) A bolted three-phase fault at bus 1. (b) A bolted single line-to-ground fault at bus 1. (c) A bolted line-to-line fault at bus 1.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Figure 3 shows the one-line diagram of a three-bus power system with generation at bus X. The magnitude of voltage at bus X is adjusted to 1.05 per unit. The scheduled loads at buses Y & Z are as on the diagram. Line impedances are marked in per unit on a 100 MVA base. i. Determine the bus voltages. Calculate branch current and power flow after 1 iteration for branch X-Y, X-Z and Y-Z. You must show all equations formulated and used in the calculations.
Microprocessor
In dc generator, is used to collect current and send it to the external circuit. О yoke bearings brushes commutator
Power factor and power rating
What is Per Unit System? In the given picture, would there be any difference in calculation of the transformers, if you choose primary or secondary side? Explain in words. 111kv 13-8 KV 13 8KV/5KV load 20MVA X= 8%. X-4%
In tan" tan M- M+ M OCT Evaluate (130 points); Use 3 decimal places. 1. The annual load of a substation is given in the following table. During each month, the power is assumed constant at an average value. Find the (a) average load and (b) the annual load factor. Annual System Load January 8 February 8 March 4 April 2 May 6 2, T- June 12 sing July 14 pha: August 14 idea September 10 imp October 8 5Y5 November 6 mac December 8 00 deliv
FINAL ANSWER IN 2 DECIMAL PLACES. ASAP. For magnetically coupled circuit below, find the 1. Thevenin impedance (express in rectangular form)2. Thevenin voltage ( express in polar form)
Define z ,P, Q
A generation station has the following daily load cycle: 20-24 16-20 12-16 10-12 6-10 0-6 Time (h) 40 X 55 45 50 40 Load (kW) Find the value of X, if the units generated between 3pm to 11pm is 290. Draw the load duration curve.