Power factor and power rating (а)Complete the table giving your answers to two decimal places.ReactiveSpecificPowerPowerLeading/LaggingpowerpowerFactorSl units ->No UnitNo UnitNAN/AMilk shed62005467.888266.660.75LaggingBarnLagging v15005851610.040.93Farmhouse1024.70Leading v-80013000.79(b)Generator sets are commonly specified to have a given specific powerrating. What is the minimum specific power rating of the diesel generatorsupplying these three loads? (Give your answer to two decimal places and select the appropriate unit)(c)What is the farm's power factor when operating at full load?

(a) In the table most of the values are given in the table and the answers we can take specific…

(а) Complete the table giving your answers to two decimal places. Reactive Specific Power Power Leading/Lagging power power Factor Sl units -> W No Unit v No Unit N/A NA Milk shed 6200 5467.88 8266.66 0.75 Lagging Lagging v Leading v Barn 1500 585 1610.04 0.93 Farmhouse 1024.70 -800 1300 0.79 (b) Generator sets are commonly specified to have a given specific powerrating. What is the minimum specific power rating of the diesel generator supplying these three loads? (Give your answer to two decimal places and select the appropriate unit) (c) What is the farm's power factor when operating at full load?

(а) Complete the table giving your answers to two decimal places. Reactive Specific Power Power Leading/Lagging power power Factor Sl units -> W No Unit v No Unit N/A NA Milk shed 6200 5467.88 8266.66 0.75 Lagging Lagging v Leading v Barn 1500 585 1610.04 0.93 Farmhouse 1024.70 -800 1300 0.79 (b) Generator sets are commonly specified to have a given specific powerrating. What is the minimum specific power rating of the diesel generator supplying these three loads? (Give your answer to two decimal places and select the appropriate unit) (c) What is the farm's power factor when operating at full load?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.13P

See similar textbooks

Related questions

Q: What is the load factor? What happens when load factor = 1?

Q: What are the typical power quality issues in the power system? What are the methods to mitigate…

A: The typical power quality issues in the power system are: Over voltage: Over voltage power increase…

Q: Please answer in typing format solution

A: Principles of Power Quality in Electrical SystemsPower quality is crucial in electrical systems,…

Q: Draw the block diagram of a load frequency control of a single area power system

A: Load-frequency control (LFC) : For large scale electric power systems with interconnected areas,…

Q: (b) Differentiate between single phase and three phase alternating current (A.C) supply for the…

A: Single Phase:Generated by a single rotating coil in a magnetic field.The coil cuts the magnetic…

Q: A three-phase uncontrolled bridge rectifier delivers power to a resistive load of 102. The output…

Q: 10. A capacitor is connected across a 120 V, 60 Hz supply. An ammeter indicates 5 A and a wattmeter…

A: Since you have posted the questions with multiple subpart so we are supposed to answer 3 subpart.

Q: 19. The correct phase sequence must be used when the power being A. reactive power. B. true power.…

A: There are three types of power: Active power: It is across the resistive elements Reactive power :…

Q: Hot-spot effect in PV strings is advantage to PV efficiency. Select one: a. True. b. False.

A: Hot-spot effect in PV strings

Q: If 3-phase transfomer configuration in figure in has the givens as listed below: E-line on high…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: What is the purpose of a power factor correction device, and how does it contribute to efficient…

A: A power factor correction device (often referred to as a capacitor bank or power factor correction…

Concept explainers

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.

Question

Power factor and power rating

(а)
Complete the table giving your answers to two decimal places.
Reactive
Specific
Power
Power
Leading/Lagging
power
power
Factor
Sl units ->
No Unit
No Unit
NA
N/A
Milk shed
6200
5467.88
8266.66
0.75
Lagging
Barn
Lagging v
1500
585
1610.04
0.93
Farmhouse
1024.70
Leading v
-800
1300
0.79
(b)
Generator sets are commonly specified to have a given specific powerrating. What is the minimum specific power rating of the diesel generator
supplying these three loads? (Give your answer to two decimal places and select the appropriate unit)
(c)
What is the farm's power factor when operating at full load?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Compensation Techniques in Transmission Line

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The reactance of a generator is given as 0.25 per-unit based on the generator’s of 18 kV, 500 MVA. Find its per-unit reactance on a base of 20 kV, 100 MVA. a. 0.0505 b. 0.0605 c. 0.0405 d. 0.0606
A synchronous generator is rated 645 MVA, 24 kV, 0.9 pf lagging. It has a synchronous reactance 1.2 . The generator is feeding full load at 0.9 pf lagging at rated voltage. Calculate: (a) Excitation emf (E,) and power angle & (b) Reictive power drawn by the load Carry out calculations in pu form and convert the result to actual values.
The one-line diagram of a simple power system is shown in Figure below. The neutral of each generator is grounded through a current-limiting reactor of 0.25/3 per unit on a 100-MVA base. The system data expressed in per unit on a common 100-MVA base is tabulated below. The generators are running on no-load at their rated voltage and rated frequency with their emfs in phase. G Stark Item Base MVA Voltage Rating X' x² 20 kV 20 kV 20/220 kV 20/220 kV 100 0.05 0.15 0.15 0.10 0.10 220 kV 0.125 0.125 0.30 0.15 0.25 025 0.7125 0.15 100 100 0.15 0.05 0.10 0.10 0.10 100 0.10 100 100 Lu La 220 kV 0.15 220 kV 0.35 100 A balanced three-phase fault at bus 3 through a fault impedance Zf= jo.I per unit. The magnitude of the fault current in amperes in phase b for this fault is: Select one: A. 345.3 B. 820.1 C. 312500 3888888 产产
b) Two synchronous generators, G2 and G2, are connected parallelly supplying a load. Generator G1 has a no-load frequency of 50.5 Hz and a slope of 300 MW/Hz. Generator G2 has a no-load frequency of 50.2 Hz and a slope of 500 MW/Hz. The load consumes 250 MW real power. (1) At what frequency does this system operate, and how much power is supplied by each of the two generators? (ii) An additional 100 MW load is added to this power system. What is the new system frequency, and how much power do G1 and G2 supply? (iii) The governor set point of G2 is changed to control system frequency back to 50 Hz. Determine the G2 governor set point.
Consider three ideal single-phase transformers (with a voltage gain of ) put together as three-phase bank as shown in Figure 3.35. Assuming positive-sequence voltages for Va,Vb, and Vc find Va,Vb, and VC. in terms of Va,Vb, and Vc, respectively. (a) Would such relationships hold for the line voltages as well? (b) Looking into the current relationships, express IaIb and Ic in terms of IaIb and Ic respectively. (C) Let S and S be the per-phase complex power output and input. respectively. Find S in terms of S.
The amplitude of the sinusoidal symmetrical ac component of the three-phase short-circuit current of an unloaded synchronous machine decreases from a high initial value to a lower steady-state value, going periods through the stages of __________ and ________ periods.
Consider a three-phase generator rated 300MVA,23kV, supplying a system load of 240 MA and 0.9 power factor lagging at 230 kV through a 330MVA,23/230Y-kV step-up transformer with a leakage reactance of 0.11 per unit. (a) Neglecting the exciting current and choosing base values at the load of 100 MVL and 230 kV. Find the phasor currents IA,IB, and IC supplied to the load in per unit. (b) By choosing the load terminal voltage IA as reference, specify the proper base for the generator circuit and determine the generator voltage V as well as the phasor currents IA,IB, and IC, from the generator. (Note: Take into account the phase shift of the transformer.) (C) Find the generator terminal voltage in kV and the real power supplied by the generator in MW. (d) By omitting the transformer phase shift altogether, check to see whether you get the same magnitude of generator terminal voltage and real power delivered by the generator.
To convert a per-unit impedance from old to new base values, the equation to be used is Zp.u.new=Zp.u.old(VbaseoldVbasenew)2(SbasenewSbaseold)Zp.u.new=Zp.u.old(VbaseoldVbasenew)2(SbasenewSbaseold)Zp.u.new=Zp.u.old(VbaseoldVbasenew)2(SbasenewSbaseold)
The direct electrical connection of the windings allows transient over voltages to pass through the auto transfonner more easily, and that is an important disadvantage of the autotransformer. (a) True (b) False
Suppose two generators supplying a load. Generator-1 has a no-load frequency of 61.5 Hz and a slopesp1 of 1 MW/Hz. Generator-2 has a no-load frequency of 62 Hz and a slope sp2 of 1MW/Hz. The twogenerators are supplying a real load totaling 2.5 MW at 0.8 PF lagging. Draw the resulting systempower-frequency or house-diagrams. Determine (a) at what frequency is the system operating, andhow much power is supplied by each of the generators? (b) if an additional 0.75-MW load wereattached to this power system. What would the new system frequency be, and how much powerwould the each generator supply now? (c) with the system in the configuration described in part (b),what will the system frequency and generators power be if the governor set points on generator-1 areincreased by 0.5 Hz?
Two turbo alternators rated for 140 MW and 260 MW have gov ernor drop characteristics of 5% from no load to full load. They are connected in parallel to share a load of 250 MW. Determine the load shared by each machine suming free governing action.
The per unit impedance of a generator on a 60 MVA, 20 kV base is j0.09 p.u. The per unit impedance to a 100 MVA, 20 kV base will be (a.) j0.054 p.u. (c.) j 1.5 p.u. (b.) j0.54 p.u. (d.) j0.15 p.u.