Q5. A force of 1500 KN is applied on a steel bar, young's modulus is 200 G Pa. Length of the bar is 5000 mm andradius is 100 mm. Calculate the clastic strain energy due to the applied load.Marks (15)CLO3- C4 (Analysis) - PLO2 (Problem Analysis)BC

Answered: Image /qna-images/answer/a6255c35-197b-49c0-b20d-f8e77dcbd282.jpg

Q5.A force of 1500 KN is applicd on a stcel bar, young's modulus is 200 G Pa. Length of the bar is 5000 mm and radius is 100 mm. Calculate the elastic strain energy duc to the applied load. Marks (15) CLO3- C4 (Analysis) - PLO2 (Problem Analysis) L B C

Q5.A force of 1500 KN is applicd on a stcel bar, young's modulus is 200 G Pa. Length of the bar is 5000 mm and radius is 100 mm. Calculate the elastic strain energy duc to the applied load. Marks (15) CLO3- C4 (Analysis) - PLO2 (Problem Analysis) L B C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A rectangular steel block is 4inches long in the x direction, 2inches long in the y direction, and…

Q: A prismatic bar with a circular cross section is loaded by tensile forces P 65kN. The bar has length…

A: Given, Initial length of the bar, Li=1.75 m Initial diameter of the bar, di=32 mm=0.032 m Applied…

Q: 2. A load of 12 kN falls 5 mm onto the end of a vertical bar 250 mm heigh and 2500 mm² cross-…

Q: The pin-connectsed structure consists of a rigid bar ABCD and two bronze alloy [E = 100 GPa] bares,…

A: GivenE=100GPaA=340mm2L1=810mmL2=1080mma=480mmb=38mmc=600mmσlim=165MPa

Q: 3- For the plane truss with an inclined support shown below, solve for the nodal displacements and…

Q: Consider the same truss again here as shown below. Suppose that the cross-sectional area of the…

A: Given Data Cross-sectional area of first element is : A1=200 mm2 Young's modulus is : E1=55…

Q: The cross - sectional area of an aluminum bar is 170 mm². It carries an axial load at the positions…

A: Given: Cross-sectional area of an aluminium bar, A= 170 mm^2 E= 80 GPa= 80000 MPa Solution: Lets…

Q: 330k 198k 132k N 16 in.- 12 in. 12 in. E = 29×10086 D = 1.07 in (bigger rod) D=107mind(570.618 in.…

Q: A steel bar of square section is subjected to an axial compressive load of 100 kN. Under this load,…

Q: 2. A straight bar with given loading is shown in the diagram. And the cross section area A=300mm?.…

Q: There is a plastic rod having a length of Lred, and a diheter of d,oa. The elastic modulus of the…

A: As per given question Length of rod=0.22m Diameters of rod =0.014m P=350N Ep=2.7gpa Vp=0.4 We have…

Q: A stepped bar is subjected to an axial tensile force of 40000 lb. Compute the increase in stress due…

Q: Q4: The composite bar shown is firmly attached to unyielding supports. An axial force P 6 kN is…

Q: 3. A bronze bar having a cross-sectional, area of 200 mm? carries the axial loads shown in the…

Q: Calculate the compression resistance in kN of the cross-section of a stocky universal beam (UB)…

Q: A rectangular steel block is 4inches long in the x direction, 2inches long in the y direction, and…

A: Solution to first three sub-parts as per our company policy:

Q: c) A solid homogeneous truss tie-rod has a diameter of 9.52 mm and an original length of 1.75 m…

A: Given Data The daimeter of truss tie rod is:d=9.52 mm The length is:l=1.75 m The stress experienced…

Q: (b) a. A member ABCD is subjected to point loads as shown in figure Task 2.b. Calculate (i) Force P…

Q: The vertical rectangular cross section column shown in Fig. Ql-B is pinned at both ends. Assuming…

A: **According to the guidelines we can answer only three sub-parts, please re-post the question to the…

Q: 10. A steel rectangular block, a = 2.4cm wide and b =1.2 cm deep, is subjected to an axial tensile…

A: GIVEN :- Width : a=2.4 cm=0.024 mdepth : b=1.2 cm=0.012 mLength : L=10 cm=0.1 mincrease in length :…

Q: 5. Calculate the MS of the member below for tension in yield, if the material is Al 7075-T6 and the…

A: To calculate the margin of safety for a member for tension in yield with the material AI 7075-T 6.We…

Q: FIND THE AREA USING SODERBERG PRINCIPLE

A: Given data; P1=20 kNP2=100 kNσyt=240 MPaσe=160MPaF.O.S=2

Q: 3. Find the young's modulus of a bars a rod of diameter 25 mm and of length 250 mm which is…

A: Givend=25mmL=250mmP=50kN∆=0.3mmif E=2×105 N/mm2

Q: The weight is suspended from steel and aluminum wires, each having the same initial length of 3 m…

A: According to the given data WireArea(mm2)allowable stress(GPa)Modulus of…

Q: 2) A circular bar that is 120 in long, with 2 in diameter, and modulus 28 x 106 psi is subject to a…

Q: 4. A standard brick (dimensions 200mm x 100mm x 65mm) is compressed lengthwise by a force P as…

Q: If an isotropic material has a shear modulus of 27 Gpa and a Poisson's ratio of 0.42, calculate its…

Q: Q4) In buckling experiment a steel column ( E-210 Gpa) was examined in pin-fixed method. It endured…

A: Givensteel columnE=210…

Q: A vertical steel bar shown in figure Q1 is subiected to a compressive load of 75 kN. If the stress…

Q: The Ultimate strength of the material * is

A: Basics of Stress-strain diagram.

Q: Ql:A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. Axial loads are…

A: Answer: The largest allowable value of P is 7.12225 kN.

Q: Q4/ Determine the total elongation of an initially straight bar of length 100 cm, with diameter is…

Q: Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution…

Q: A solid steel bar 250 mm long is 10 mm square over part of its length, the remainder being circular…

A: Answer: (a) The load P is 20 kN. (b) The total extension of the bar is 0.13 mm. (c) The length of…

Q: P solid, see Fig below. The outer diameter of the hollow and solid sections is 6 cm and the inner A…

A: Given: The outer diameter of the solid and hollow section: →Do=6 Cm=0.06 m The inner diameter of the…

Q: A steel circular tube is subjected to torsion by torques T applied at the ends as shown below. The…

A: This problem is related to the torsion of the shaft. torsion, when the twisting moment is applied to…

Q: Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution…

Q: A helical spring used in an automobile suspension is having a wire diameter of 7mm and an outside…

Q: Q2: Figure (2) shows an isometric view of a crankshaft that is actuated by the vertical force acting…

Q: For the steel block (Length L = 5-meter, Width W = 1 meter, Height H = 1 meter) with compression…

Q: A circular tube of aluminum is subjected to torsion by torques T applied at both end. The bar 0.5m…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

Q5. A force of 1500 KN is applied on a steel bar, young's modulus is 200 G Pa. Length of the bar is 5000 mm and
radius is 100 mm. Calculate the clastic strain energy due to the applied load.
Marks (15)
CLO3- C4 (Analysis) - PLO2 (Problem Analysis)
B
C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. Load-bearing part, as shown in Figure 2.1, find 2.1 Reaction force acting on points A and B 2.2 Then Panyasil recommends to modify the additional section as shown in Figure 2.2 to reduce the reaction force on point B can be reduced. Do students think that Panyasilp's statement is correct (Photo 2.1,2.2 L1=120mm L2=150mm)
Give me all a,b and c right solutions id=6k=1.2
In constructing a large mobile, Jude hangs an aluminum sphere of mass 6.0kg from a vertical steel wire 0.50m long and 2.5 x10−3 cm2 in cross-sectional area. On the bottom of the sphere, he attaches a similar steel wire, from which he hangs a brass cube of mass 10.0kg. For each wire, compute:(a) The tensile strain and(b) The elongation
Problem 5: A circular bar of diameter 2.5 cm is subjected to an axial tension of 20 kN. If the material elastic with a Young's modulus E=70 GN/m². Estimate the percentage elongation.
Can you please answer question B, thank you
AB and CD caps of the same material are tightly fitted on both ends of the 24 mm diameter AD steel bar. a) Find the pull force P that will make the total elongation of the system 0.04 mm. b) Calculate the extension amount of BC part by the force P you found. Take the elastic modulus E = 200 GPa. 36mm 24mmr 36mm 48mm D 28mm
2-A wheel of diameter d and width w carrying a load F rolls on a flat rail. Estimate the maximum contact pressure for these materials. Por vedit -3D d 5 in 150 mm 3 in W 2 in 40 mm 1.25 in F 600 lbf 2 kN 250 lbf Wheel Material Steel Steel Cast iron Rail Material Steel Cast iron Cast iron.
A solid homogeneous truss tie-rod has a diameter of 9.52 mm and an original length of 1.75 m experiences a stress of 600 MPa when placed under tension. If the material used for the truss tie-rod has a Young's Modulus, E, of 5.8 x 1011 N/m?, calculate: (i) the tie-rod's extension in millimetres (mm); (ii) the strain energy (U) in Joules; and (ii) the strain energy per unit volume (U/V) in Joules per cubic metre (m³). Give your answers to two decimal places.
A bar of 1000 mm length and 40 mm diameter is cen- trally bored for 300 mm length at one end at a diameter of 20 mm. Young's modulus of the material is 2 x 105 N/mm?. If the bar is loaded axially with a load of 30 kN the extension produced is (A) 0.1136 mm (C) 0.1478 mm (B) 0.1313 mm (D) 0.1542 mm
A steel bar of 30 mm * 30 mm square cross section is subjected to an axial compressive load of 300KN. If the length of the bar is 3m and E=200GPa find contraction of the bar.
Q2/B Acolumn of rainforced concrete has steel reinforcing rods running through its entire length and parallel to the column axis. If concrete has (E) of 15GPa and tensile strength of 2.8 MPa and the steel rods has (E) of (210) GPa and tensile strength of(400) GPa Determine the modulus of elasticity and tensile strength of composite if the steel rods occupy 10% of cross-sectional area of the column 021 21
This question is from the subject Theory of Elasticity