Q5. A material is made in circular rod form of diameter 1.5 cm and 200mm long. It is fixed on the Universal Testing Machine. When SKN force is applied on the material, its length became 201.5 mm, material shows maximum stress 550MPa. Find [3] (1) Stress (ii) Youngs modulus (iii) Max force

Q: Hammer arm length = 100 cm Q3/ the accompanying table contain data abtained during a tensile test…

A:

Q: A tensile test is performed on a metal specimen 10 mm in diameter using a gage length of 50 mm (see…

A:

Q: 3. Stress – Strain Behavior Consider the brass alloy for which the stress-strain behavior is shown…

A: Dear student,                     According to the guidelines I am allowed to answer only three…

Q: S A round steel alloy bar with a diameter of 19 mm and a gauge length of 76 mm was subjected to…

A: Given data:- Original length, L=76mm Original diameter, d=19mm ⇒Original area,…

Q: 2 (d) shows a typical aluminum stress-strain curve. A mechanical engineer has to carry out a tensile…

A: To design the appropriate rod. Given:σallow=400 MPaF=20 KNL=380 cm∆L=0.8 cm

Q: In reference to the Tensile Test result for a steel sample shown in the figure below. If the…

A: Given dataDiameter of sample = 12 mmFrom the Force-Elongation graphMaximum force applied =70 kN

Q: What is the whal factor of a spring if it has the characteristics average diameter 200 mm, wire…

A:

Q: 4. Plot the shear stress- shear strain curve for ductile material showing on it: modulus of…

A: Solution to first Question 4 as per our organization rules: 4 The shear stress -shear strain curve…

Q: The following data was obtained tensile test on a specimen of 6 mm diameter and gauge length Lo=30…

A: Since there are many subquestions asked, the first one statement of questions will be answered.…

Q: Stress (MPa) Graph 1 - Stress/Strain plot 400 320 300 200 100 0 (a) 51.472kN (b) 205.89kN (c) 25735N…

A:

Q: The above load-elongation data were obtained for a specimen with Lo = 0.1 m and To 7 mm. Plot the…

A: Given:Original length of the specimen, Lo=0.1 m=100 mmOriginal radius of the specimen, ro=7…

Q: Q1. A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of 350…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: A steel pipe with an outside diameter of 115 mm and an inside diameter of 105 mm supports the…

A: Now we have the moment equation asMx=16×510-11×230=5630kN.mm=5.63kN.mMy=-20×510=-10200 kN.mm=-10.2…

Q: (sigma) = 90   40 0                    40 −50 0                    0     0   0 MPa a. Plot the shear…

A:

Q: A straight bar of uniform cross sectionis tested in tension. The bar's cross sectional is 6.5 square…

A:

Q: Explain the phases shown in the attached image of a stress strain cureve for 0.15% carbon steel

A:

Q: Assume the reaction forces at the origin were solved to be Rf = [325, 100, 0] N and Rm [10, -2, 5]…

A: To determine the normal stress in the x-direction Ox for element 2, we need to calculate the force…

Q: A steel component is subjected to alternate cyclical loading. The steel follows Basquin's law for…

A: Answer: (a) The stress ratio, the stress amplitude and the mean stress: R = -1 σa = 213 MPa σm = 0…

Q: Determine the tensile yield strength (0.2% offset) and the maximum strength of a metal alloy having…

A: Yield Strength : Yield strength is the maximum stress that can be applied before it begins to…

Q: 1. Stress, Soratn care 2- clastic Zone 3. yield spresscoys 4- plastic 2one 5- UItimate Stress Cous…

A: To find Elastic zone Plastic zone Limit of proptionality Yield stress ultimate stress

Q: Q.3. A cylindrical specimen of cold-worked Brass has a tensile strength of 500 MPa. If the specimen…

A: Given:- Tensile strength =500 MPa Original radius, ro=10.6mm To find:- Radius after deformation, rd

Q: Please solve in detail. Don't use chatgpt,The Free body diagram must be drawn.

A: Free-body Diagram:  Note: I hope this helps. Thank you.

Q: 4. A mild steel material is tested using universal testing machine & the following data was obtained…

A: As per our guidelines we are suppose to answer first three sub parts. a) The Young's modulus (E) is…

Q: SPECIMEN YIELD POINT ULTIMATE STRESS ТOTAL STRAI DEFORMATIO N or change in length (mm) SAMPLE Nomina…

A: Given data We have to find the stress at yield point, stress at ultimate stress and the % strain.

Q: yauges system mounted at a point on a structural member that is subjected to multiaxial stresses,…

A:

Q: For a material, Young's modulus is given as 3.2 X 105 N/mm2 and Poisson's ratio is (1/4) Calculate…

A: Given data : Youngs modulus=EPoisson's ratio =μTo find :Bulk modulus

Q: A tensile test is conducted for a metal wire which has a diameter of 4.5, the maximum recorded force…

A: Given , Diameter (D) = 4.5 mm Maximum force (F) = 3700 N It is asked to find UTS point.

Q: A tensile test is conducted for a metal wire which has a diameter of 4.5, the maximum recorded force…

A: Given data: D=4.5 mmF=1300 N   It is required to determine the ultimate tensile stress of the…

Q: The maximum tensile stress o, from bending of a simply supported beam with length L and circular…

A:

Q: You are an engineering intern at a manufacturer of mechanical tools, your senior engineer asked you…

A: Data given -  d = 20 mm  Di = 75 mm  L = 250 mm  F = 4kN

Q: Q.1: Find out Young's modulus value of a material whose elastic stress and strains are 4 N/m² and…

A: Given, Elastic stress = σ = 4 N/m2 Strain = ε = 0.30   In the elastic region, as per Hooke's law,…

Q: is positioned at point A for strain measurement. The orientation of the strain rosette is shown in…

A: