yauges system mounted at a point on a structural member that is subjected to multiaxial stresses, where we have the following readings: Ex = 6.686 x10-4; &y = 3.0 x10-4; ɛz = - 6.857 x10-5; %3D %3D Yxy 2.580 x10-3; !! Determine the stress components if the member is made of an isotropic material with linear elastic behavior having the following elastic properties: Young's modulus E = 70 Gpa and Poisson's ratio v = 0.29;

yauges system mounted at a point on a structural member that is subjected to multiaxial stresses, where we have the following readings: Ex = 6.686 x10-4; &y = 3.0 x10-4; ɛz = - 6.857 x10-5; %3D %3D Yxy 2.580 x10-3; !! Determine the stress components if the member is made of an isotropic material with linear elastic behavior having the following elastic properties: Young's modulus E = 70 Gpa and Poisson's ratio v = 0.29;

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The plastic distorts as shown by the dashed lines. (Figure 1) The dimensions are L = 460 mm, H = 345 mm, d₁ = 3 mm, d₂ = 5 mm, d3 = 13 mm, d4 = 8 mm, d5 = 3 mm, and de = 6 mm. Figure H B A dz dg ds + 1 of 1 Part A Determine the shear strain Yzy at corner A. Express your answer to three significant figures and include appropriate units. ol Di μA ? (YA)zy = Value Units Submit Request Answer Part B Determine the shear strain Yzy at corner B. Express your answer to three significant figures and include appropriate units. Di μA ? (YB)Ty = Value Units Submit Provide Feedback Request Answer
The principal stresses shown below are calculated at two different cross sections of a brittle machine part. Determine if the cross section A or B is safer (Sy = 50 MPa, Sut = 100 MPa, and Suc = 200 MPa). 0,50 MPa + 0₂ = -20 MPa A 0₂=-20 MPa 0₁ = 50 MPa a, 20 MPa - ₂ =-120 MPa B 0-120 MPa a₁ = 20 MPa
Q4 Beta =111 Please provide justified answer asap to get a upvote
For a given homogeneous, isotropic, linearly elastic material, E = 15e6 psi and v = 0.3. Solve for the shear modulus. 2.1.1 Homogeneous, isotropic, linearly elastic materials For specimens undergoing small deformations, the stress-strain diagram often ex- hibits a linear behavior. Although this is a very crude approximation to the behavior of actual materials, it is a convenient assumption that is often used for preliminary evaluation. A linear relationship between stress and strain can be expressed as 01 = E €1, (2.1) where the coefficient of proportionality, E, is called Young's modulus or modulus of elasticity. Since strains are non-dimensional quantities, this coefficient has the same units as stress quantities, i.e., Pa. This linear relationship is known as Hooke's law. The elongation of a bar in the direction of the applied stress is accompanied by a lateral contraction that is also proportional to the applied stress. The resulting defor- mations for this uniaxial state of stress…
i li. الامتحان هو سؤالان فقط Q. 1: If a material is cast iron (ultimate tensile strength = 300 Mpa, ultimate compressive strength - 900 Mpa) and the stress state at a point is shown in Fig. 1. Using a graphical method, find safety factor against static failure using 100 Mpa (a) Rankine failure theory (b) Coloumb - Mohr theory (c) Modified Coloumb - Mohr theory 50 Мра إضافة ملف Q.2 For a rotating shaft of diameter 15 mm as shown in Fig. 2. If the material is AISI-1045 CD, Find the safety factor II >
Correctly solve by using correct expression
A strain gauges system mounted at a point on a structural member that is subjected to multiaxial stress, where we have the following readings: Ex = 3.8 x104; &y = 5.5 x10-5; Ez = - 7.5 x10-5; Yy = 9.1 x104; %3D Determine the stress components if the member is made of an isotropic material with linear elastic behavior having the following elastic properties: Young's modulus E = 200 Gpa and Poisson's ratio v = 0.3; Select one: Ох %3D -100 Мра; оу %3D -50 Мра; о, %3D 30 Мра; Тху 3D 70 Мра; Ox = -75 Mpa; o, = -50 Mpa; 0z = 40 Mpa; Ty = 80 Mpa3; Oy = 300 Mpa; oy = -150 Mpa; 0z 3 100 Мра;B тyу = 100 Mpa; TOSHIBA
A steel component is subjected to alternate cyclical loading. The steel follows Basquin's law for high cycle fatigue, o, x N = C, (where the stress amplitude is in MPa). Ignore the geometric detail and assume that Marin's modifying factors are all equal to 1. You are given the minimum stress ain = -213 MPa, the maximum stress omax = 213 MPa. The material data are Tensile strength oUTS = 539 MPa, Basquin's constant c, = 875 MPa, Basquin's exponent a = 0.085. a) Calculate the stress ratio R, the stress amplitude o, in MPa and the mean stress am in MPa. The answers are acceptable with a tolerance of 0.01 for R and of 1 MPa the stresses. R: MPa MPа b) Calculate the corresponding life, in 10° cycles, (tolerance of 0.1 106 cycles) N :
1) The triangular plane stress problem connected to a spring, is subjected to a uniformly distributed load and two point forces. Calculate the nodal displacements and the spring force using two triangular finite elements. k = 3x105 kN/m (spring constant) h = 0.20 m (thickness) E = 3x107 kN/m² (modulus of elasticity) v = 0.20 (Poisson's ratio) 1.5 m 40 kN 30 kN/m 50 kN 2 m 2 m