Q5-(A)-Select the correct answer for the alternatives given. 1- he secondary winding of which of the following transformer is always kept close a)- power transformer b)- auto-transformer c)- current transformer d)- distribution transformer 2-In transformer ,the load current at maximum efficiency is equal to rated load current multiplied by PL d)- Pcu a)- Peu PL b)- [ Pcu Pcu Pi 3-which of the following does not change in transformer a)-current b)-voltage c)- frequency d)-all of the above 4-The full-load copper loss and iron loss of transformer are 6400w and 500w respectively. The copper loss and iron loss at half load will be respectively. a)-(3200 w and 2500 w) b)- (1600 w and 1250 w) c)- (1600 w and 5000w ) d)- (3200 w and 1250 w)

Q5-(A)-Select the correct answer for the alternatives given. 1- he secondary winding of which of the following transformer is always kept close a)- power transformer b)- auto-transformer c)- current transformer d)- distribution transformer 2-In transformer ,the load current at maximum efficiency is equal to rated load current multiplied by PL d)- Pcu a)- Peu PL b)- [ Pcu Pcu Pi 3-which of the following does not change in transformer a)-current b)-voltage c)- frequency d)-all of the above 4-The full-load copper loss and iron loss of transformer are 6400w and 500w respectively. The copper loss and iron loss at half load will be respectively. a)-(3200 w and 2500 w) b)- (1600 w and 1250 w) c)- (1600 w and 5000w ) d)- (3200 w and 1250 w)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

"Electrical machines/ I need a complete and clear solution for all sub -questions of a single question. Thank you."
The turns ratio of a particular transformer is less than 1. Where would you expect to see this type of transformer? OI. A 0 0 0 0 0 Power Plant K Generation II. A and B III. B IV. B and C V. C VI. C and A A Station High-Voltage Power Lines Transmission B Substation C Distribution Power Lines ( .00 Industrial Consumer Commercial Consumer Residential Consumer Distribution
A Buck converter has an output power of 1950 Watts, and a source voltage of 1000V (the constant DC voltage). Using the information provided and the "“transformer-like" relationships derived in class, estimate the corresponding load currents for the following duty ratios: a) D=0.35 b) D=0.9 c) D=0.5
Q5:Choose the correct answer from the given alternatives (answer five only) 1.In an ideal transformer, (a) windings have no resistance (b) core has infinite permeability (d) all of the above. (c) core has no losses 2. The primary and secondary induced e.m.fs. El and E2 in a two-winding transformer are always: (a) equal in magnitude (b) in-phase with each other (c) antiphase with each other (d) determined by load on transformer secondary. 3. In relation to a transformer, the ratio 20 : 1 indicates that (a) there are 20 turns on primary one turn on secondary (b) secondary voltage is 1/20th of primary voltage (c) primary current is 20 times greater than the secondary current. (d) for every 20 turns on primary, there is one turn on secondary. 4. A transformer has negative voltage regulation when its load power factor is: (a) zero (b) lagging. (d) unity (c) leading
Electric machines/ I need to choose the correct answer with a brief explanation for it.
please solve the question lmlmlmlm
Choose the correct answer from the given alternative: 1. In an ideal transformer, (a) windings have no resistance (c) core has no losses (b) core has infinite permeability (d) all of the above. 2. The primary and secondary induced e.m.fs. El and E2 in a two-winding transformer are always: (a) equal in magnitude (b) in-phase with each other (c) antiphase with each other (d) determined by load on transformer secondary. 3. In relation to a transformer, the ratio 20: 1 indicates that (a) there are 20 turns on primary one turn on secondary (b) secondary voltage is 1/20th of primary voltage (c) primary current is 20 times greater than the secondary current. (d) for every 20 turns on primary, there is one turn on secondary. 4. A transformer has negative voltage regulation when its load power factor is: (a) zero (b) lagging. (d) unity (c) leading 5. During short-circuit test, the iron loss of a transformer is negligible because: (a) the entire input is just sufficient to meet Cu losses only…
A transformer with a central tap was purchased that provides a voltage of 11Vac between the central tap and either of its ends. We want to make a regulated voltage source that is ± 12Vdc ... is it possible to make the source with the transformer you bought or need to go change it? What would you recommend?What are the minimum components that you must buy to make the voltage source? Just provide your view please
A 25 kVA, 2 kV(rms)/100 V(rms) single phase transformer is connected between a 120 V(rms) utility supply and a resistive load. The load current was measured to be 20 A(rms). i. Determine the active power of the load. ii. Determine the primary RMS current. iii. Determine the equivalent resistance of the transformer as seen by the utility supply.