Q4-A vertical force of 178 Nis applied to a pipe wrench whose handleis vertical to the z-axis as shown in figure (4), Determine the principal stresses at point Ain the cross section where the pipe threads begin. The pipe has outside and inside diameters of 3.34 cmand 2.66 cm. y 30.5 сm 22.8 cm B 178 N Figure (4)

Q4-A vertical force of 178 Nis applied to a pipe wrench whose handleis vertical to the z-axis as shown in figure (4), Determine the principal stresses at point Ain the cross section where the pipe threads begin. The pipe has outside and inside diameters of 3.34 cmand 2.66 cm. y 30.5 сm 22.8 cm B 178 N Figure (4)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A machine component is fabricated from a bent tube as shown below. One part of the tube lies along the z- axis, and the other part is parallel to the y-axis. The outside diameter of the tube is do 122 mm and its inside diameter is dį = 108 mm. A force F = 8.5 kN acts along a line from point to point D. Determine the principal stresses and the absolute maximum shear stresses at points A and B. Note that point A lies along the y-axis and point Blies along the x-axis. Given: • L₁ 258 mm L₂ = 118 mm • L -281 mm LA-602 mm 4 P (α₂₁)A- (₁2) A (Tmax) A L2 Z ²1 00 B L₁7 number (rtol=0,01, atol=1e-05) number (rtol-0.01, atol-1e-05) number (rtol-0.01 atol-le-057 F 0 MPA LA D L3 y 0 0
Need only handwritten solution only (not typed one).
For the assembly shown in Figure 2, the cross section of the pipe at section B has outer diameter of 100 mm and inner diameter of 80 mm. points N and L are located on X-axis at outer surface of the pipe while points K and M are located on z-axis at outer surface of the pipe. At which point of the four (K, L, M or N) the principle stresses are largest. Calculate the principle stresses at this point.
Read the question carefully and give me answer according to the question
I need the answer as soon as possible
.An element in the boiler is triaxially stressed, the stresses distribution is given by (see Figure 1). Oxx = 75 MPa; on = 60 MPa; 0 = 50 MPa; Try = 25 MPa; tyz = - 25 MPa; ta = 0 MPa. determine the components of this stress state on a x'y' z' coordinate axes system described by the following direction cosines. y 2/3 -2/3 -1/3 2/3 1/3 2/3 -1/3 -2/3 2/3 y' Compute also the magnitudes and directions of the principal stresses. 60 MPa 25 MPа 75 MPa 50 MPa 25 MPа Figure 1
A torque and two forces seen in the figure are applied. the diameter is 65mm. Determine the principal stresses And the maximum shear stress at K.
4- The cross-section of the ABCD element in the figure is a circle with a diameter of 6 cm. The force of P-500 N is in the x-z plane. The CD segment is parallel to the y-axis. In line with the information given, a- Find the most critical points in section A. b- Calculate the normal and shear stresses at the most critical points in section A. c- Calculate the principal stresses at the specified points. d- Check the section with the Tresca Hypothesis. em = 95 MPa 75 cm B A N 50 cm 10 40 cm P
nc./Johan H σy 7.2-1 The stresses on the bottom surface of a fuel tanker (figure part a) are known to be o = 7750 psi, = 1175 psi, and 7 xy = 940 psi (figure part b). Determine the stresses acting on an element oriented at an angle = 55° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle 0. (a) PROBLEM 7.2-1 (b) 1175 psi Ţ 940 psi 7750 psi 7.2-5 The stresses acting on element A on the web of a train rail (see figure part a) are found to be 6500 psi tension in the horizontal direction and 18,500 psi com- pression in the vertical direction (see figure part b). Also, shear stresses with a magnitude of 3800 psi act in the directions shown. Determine the stresses acting on an element ori- ented at a counterclockwise angle of 30° from the horizontal. Show these stresses on a sketch of an ele- ment oriented at this angle. Cross Section (a) PROBLEM 7.2-5 B A Side View A (b) 18,500 psi 76500 psi 3800 psi
pru 7 Oy enüz žvaplanmadı Ot .00 üzerinden aretlenmiş Txy Soruyu aretle Ka Tnt Ox On (a) (b) On the surface of a structural member, stresses are given as ox=61 MPa, oy=32,7 MPa and Txy=-28,1 as shown in figure (a). Determine the maximum principal stress (MPa). Note: If the stress is compressive, use - sign. Yanıt:
When there is a plane stress condition as shown in the figure, display this stress in the form of the maximum in-plane shear stress and the corresponding average vertical stress.
5 Figure 5 shows a thick cylinder of 50 mm internal radius and 115 mm outer radius is subjected to an internal pressure of 60 MN/m² and an extemal pressure of 30 MN/m?. Determine the hoop and radial stresses at the inside and outside of the cylinder together with the longitudinal stress if the cylinder is assumed to have closed ends using analytical and graphical approaches.