30 MN/m26OMN/mBFigure 5 5Figure 5 shows a thick cylinder of 50 mm internal radius and 115 mm outer radiusis subjected to an internal pressure of 60 MN/m² and an extemal pressure of 30 MN/m?.Determine the hoop and radial stresses at the inside and outside of the cylindertogether with the longitudinal stress if the cylinder is assumed to have closed endsusing analytical and graphical approaches.

Given data Inner radius = 50 mmOuter radius = 115 mmInternal Pressure =60 MN/m2External Pressure =…

Figure 5 shows a thick cylinder of 50 mm internal radius and 115 mm outer radius is subjected to an internal pressure of 60 MN/m² and an external pressure of 30 MN/m². Determine the hoop and radial stresses at the inside and outside of the cylinder together with the longitudinal stress if the cylinder is assumed to have closed ends using analytical and graphical approaches.

Figure 5 shows a thick cylinder of 50 mm internal radius and 115 mm outer radius is subjected to an internal pressure of 60 MN/m² and an external pressure of 30 MN/m². Determine the hoop and radial stresses at the inside and outside of the cylinder together with the longitudinal stress if the cylinder is assumed to have closed ends using analytical and graphical approaches.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A circular bracket with a diameter of 100 mm is fixed to a wall as shown in the figure below. Determine and draw the state of stresses in small infinitesimal cubic elements located at pooints M and N on the cross section A.
Read the question carefully and give me answer according to the question
(3) The cantilever bar as shown on next page is made of a brittle material. At D, Fx-300 lb. F-250 lb, and F-100 lb. Determine the precise location of critical stress element at the cross section at A. Determine the magnitude for each of the stress components considering the stress concentration at A. Find the principal stresses and the maximum shear stress at this location. 2 in 1-in dia. -in R. 12 in
The tank shown in the figure shown is fabricated from a steel plate. a. Determine the maximum longitudinal stress caused by an internal pressure of 1.2MPA if the steel plate has a thickness of 10mm. b. Determine the maximum circumferential stress caused by an internal pressure of 1.2MPA, if the stress plate has a thickness of 10mm. c. Determine the minimum thickness plate which maybe used if the stress is limited to 40MPA and the internal pressure is 1.5MPA. 1400 mm 400 mm 600 mm
Q4-A vertical force of 178 Nis applied to a pipe wrench whose handleis vertical to the z-axis as shown in figure (4), Determine the principal stresses at point Ain the cross section where the pipe threads begin. The pipe has outside and inside diameters of 3.34 cmand 2.66 cm.
This is Mechanical Engineering. Please answer with clear work and answers. Thank you
Figure Q5 shows a thick cylinder of 50 mm internal radius and 130 mm outer radius is subjected to an internal pressure of 60 MN/m2 and an external pressure of 30 MN/m2. Determine the hoop and radial stresses at the inside and outside of the cylinder together with the longitudinal stress if the cylinder is assumed to have closed ends using analytical and graphical approaches
attached can solve wrong
I need it handwritten and correct or skip please only handwritten handwritten handwritten handwritten otherwise dislikfor sure
The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are S, = 20 MPa, S, = 24 MPa, and Sy = 29 MPa. Assume ß = tan = 21.8°, a = 5, and b = 2. Using the equilibrium equation approach, determine the normal and shear stresses o (positive if tensile, negative if compressive) and z (magnitude only) at this point on the inclined plane shown. Answers: i MPa, T = i MPа.
Define the main difference between thick and thin cylinders and give an example for each type of cylinder Derive the expression of longitudinal stress, o, for a closed thick cylinder which has inner radius, R₁ and outer radius, R₂ and subjected to internal pressure only. Figure Q3 shows a cross section of composite cylinder that is made by shrinking a tube of 330 mm internal diameter and 50 mm thick over another tube of 330 mm external diameter and 50 mm thick. The radial pressure at the common surface, after shrinking is 180 MPa. Suppose the compound cylinder is subjected to an internal fluid pressure of 1200 MPa, determine; i) the hoop stresses at inner radius and outer radius of inner cylinder, ii) the hoop stresses at inner radius and outer radius of outer cylinder. Ro P Figure Q3 R₁
The foundation bolt is shown in the below figure a force F = 300 N. The bolt material is wire of diameter d = 6 mm to a radius R = 10 mm in the eye and at the shank. Determine the stresses at the inner and outer surfaces at section A-A. FA B