Q4) A SI engine four-stroke cycle V8, 0.005m3 displacement, mounted on a hydraulic dynamometer has an output of 53,6 kW at 4050 RPM. Water absorbs the energy output of the engine as it flows through the dynamometer at a rate of 0.113 m3 per minute. The dynamometer has an efficiency of 93% and the water enters at a temperature of 20°C.Calculate: (a) Exit temperature of the water. [°C] (b) Torque output of the engine at this condition. [N.m] (c) What is bmep at this condition? [kPa] *

Q4) A SI engine four-stroke cycle V8, 0.005m3 displacement, mounted on a hydraulic dynamometer has an output of 53,6 kW at 4050 RPM. Water absorbs the energy output of the engine as it flows through the dynamometer at a rate of 0.113 m3 per minute. The dynamometer has an efficiency of 93% and the water enters at a temperature of 20°C.Calculate: (a) Exit temperature of the water. [°C] (b) Torque output of the engine at this condition. [N.m] (c) What is bmep at this condition? [kPa] *

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A rection turbine has guide vane angle 30° the runner blades make an angle of 80° relative to the tanget at inlet .the blades width at inlet is 1/4 of the outer diameter .the water does not have any tanget velocity at outlet.the head is 25 m and the rotational speed of the runner is 16.67 rotation per second (rps) the turbine efficiency is 88% determine the runner diameter at the inlet and the power developed by this turbine
4. A conventional hydropower station in a dam impounds 390 ft of fresh water and has a flow of 24,720 cubic feet per second. a. What is the maximum possible amount of power (in MW) that can be developed by a turbine installed at this station? b. Calculate the power specific speed Nóp assuming a synchronous speed of 90 rpm and determine the appropriate turbine type (Pelton, Francis, or Kaplan) for this installation. c. If the turbine efficiency is 92.7%, what is the actual power developed (in MW)?
5.16. For a centrifugal compressor rotating at 2500 rpm, find the compression ratio for the following specifications. T = 300 K; 79 (volumetric flow rate)=1.25 m³/s and t (the thickness of the flow section at the exit) = 0.15 m. = 0.85; r, = 0.55; ra = 0.015; B, 60°,
The shaft rotational speed of a 3.0Li Gasoline engine operating on a 4 stroke cycle is 3000rpm. Determine the engine's volume displacement.
Example -5.2- It is required to pump cooling water from storage pond to a condenser in a process plant situated 10 m above the level of the pond. 200 m of 74.2 mm i.d. pipe is available and the pump has the characteristics given below. The head loss in the condenser is equivalent to 16 velocity heads based on the flow in the 74.2 mm pipe. If the friction factor = 0.003, estimate the rate of flow and the power to be supplied to the pump assuming n = 0.5 Q (m³/s) 0.0028 0.0039 0.005 0.0056 0.0059 Ah (m) 23.2 21.3 18.9 15.2 11.0
An engine operating on the air standard heat engine has a heat rejection at constant volume rate of 525 KJ/kg of air used. The minimum pressure and temperature are 98 Kpa and 339 K, respectively. If the bore and stroke of 75mm x 82mm, with cycle efficiency of 56% under heat addition, according to PVn = C where n = ∞ . Determine The maximum temperature and pressure The amount of air used The work for the cycle
A single stage impulse turbine steam enters with a velocity of 420 m/s and runs at 3300 r.p.m. If the blade speed ratio is 0.44, then the diameter of the wheel in meter will be the diameter of the wheel in meter
Problem (5.1) An impulse turbine is supplied with steam at a pressure of 1.6 MPa and temperature of 250°C. The back pressure is 0.012 MPa. Nozzle efficiency is 0.9. Blade velocity coefficient K=0.8, mechanical efficiency=0.9, nozzle angle =20°. Symmetrical blades with angle 30°. Find the revolution per minute if the mean diameter of wheel is 75 cm, the blade efficiency, axial thrust per kg steam, exit loss and the stage efficiency.
Determine the ideal efficiency of a diesel engine having a cylinder with bore 200mm and stroke length is 350mm. The clearance volume is 1200cc and fuel cut-off occurs at 5% of the stroke volume. Assume y=1.4.
Problem 3: Water is fed to an inward flow reaction turbine, running at 180 rpm with a velocity of flow of 3 m/s. The diameter and width of the wheel at inlet are I m and 135 mm, respectively. Assuming the velocity of flow to be constant and radial discharge at inlet and outlet, find, (a) work done per kN of water, (b) power developed by the turbine,