Q4 A- Illustrator the rotor of the following Motors? 1- Control Differential (CD) Synchro motor. 2- Shell-type Low-inertia DC Motor B- How does power transfer to rotor in the following motor type if it happened or needed? 1- Printed-circuit (Disc) DC Motor 2- Permanent-Magnet Synchronous Motor 3- Stepper variable motor

Q4 A- Illustrator the rotor of the following Motors? 1- Control Differential (CD) Synchro motor. 2- Shell-type Low-inertia DC Motor B- How does power transfer to rotor in the following motor type if it happened or needed? 1- Printed-circuit (Disc) DC Motor 2- Permanent-Magnet Synchronous Motor 3- Stepper variable motor

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Can you solve the question step by step clearly ?
A hybrid stepper motor has four stator poles and two 5-pole permanent magnet armatures, as shown in Figure Q3. A1 armature 1 armalure 2 A2 Figure Q3 Describe how the motor can be excited by a two-phase source to rotate in the counterclockwise direction.
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC MACHINES Answer the following questions (A, B and C) depending on the topic. 1. SYNCHRONOUS MOTORS A. What is necessary to start a synchronous motor to rotate from standstill? Describe the process. B. What is meant by synchronous condenser? C. Why is it possible for synchronous motors be used as a power factor correction device and what applications do synchronous motors commonly used? Describe the operation.
Q4) A 220 V d.c. shunt motor has an armature resistance of 0.5 ohm, and runs at 850 rpm., When taking a full-load current of 32 A, the shunt field resistance is 110 ohms. Calculate the speed at which the motor runs, if (i) 1.5 ohm resister were introduced in series with the armature, (ii) 300 ohms resister were connected in series with the field winding, and load torque remaining the same throughout. Assume that field is proportional to field current. ?
A three phase, 230 V, 4-pole, 60 Hz, 10 hp, Y-connected induction motor has the following characteristics:R1 = 0.1 N,X1 = 0.3 Q, R2 = 0.2 2 X2=0.5 Rotational losses are 360 W. At a rotor speed of 1746 rpm calculate the following: „Xm = 15 2 %3D %3D %3D 1) The stator armature line current. 2) The input power factor. 3) Induced torque at full load 4) Starting torque 5) Motor efficiency
Can you solve the question step by step with clear writing ?
4. A shunt motor designed to operate at 115 V, has an armature resistance is 0.12 ohms and the motor is taking 60 A in armature current at full load. Determine the value of the external resistance to be inserted in the armature circuit so that the armature current shall not exceed twice its full load value at starting. A. 0.838 ohm C. 0.667 ohm B. 0.919 ohm D. 0.733 ohm
For a rotating brushed DC motor and from the list shown, what quantity is assumed to be proportional to the electrical current flowing in the armature? O a. Rotor Angular Velocity O b. Electro-magnetic Torque O c. Rotor Friction O d. Rotor Angular Position
Question A 440V, 4-pole, lap-wound DC series motor has 510 conductors in its armature. It has a combined armature and series field resistance of 0.5 ohms, the motor takes a current of 6.4 A. Estimate the speed of the motor if the flux is 18 mwb.