Q6-Indicate whether the following statements are true or false and correct thefalse statements.1- The characteristic (angular speed versus T) of a dc shunt motor is known as theExternal characteristics.2- When a series d.c. motor is operate without load, the armature will not run3- The generation of electricity achieved by moving a conductor in a magnetic field dueto the relation E= ILBGeneral questions4- In series d-c generator the field winding will be constructed from high number ofturns and high cross-sectional area of wire.5-Series motor maintains a more constant speed under varying load6-The armature voltage of d.c series generator is not affected by load current.7- In series d-c generator the field winding will be constructed from high number ofturns and high cross-sectional area of wire.8- If field resistance of a d.c. shunt generator is increased beyond its critical value, thegenerator output voltage will exceed its rated voltage9-The inter pole winding is connected in parallel to field winding.10- in de machine the interpole winding connected across the armature winding.

Answered: Image /qna-images/answer/6f618d93-faed-404c-87a7-25a71f1dcad6.jpg

1- The characteristic (angular speed versus T) of a dc shunt motor is known as the External characteristics. 2- When a series d.c. motor is operate without load, the armature will not run 3- The generation of electricity achieved by moving a conductor in a magnetic field due to the relation E= ILB

1- The characteristic (angular speed versus T) of a dc shunt motor is known as the External characteristics. 2- When a series d.c. motor is operate without load, the armature will not run 3- The generation of electricity achieved by moving a conductor in a magnetic field due to the relation E= ILB

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

and the armature current 14.5 A. calculate the following: a) The number of conductors on the armature b) The value of the counter-emf at full load c) The flux per pole, in milliwebers [mWb] The following details are given: 73 mm 115 mm 20 40 Armature diameter: armature length: armature slots Image Word A 1.5 hp Permanent magnet motor generates a voltage of 90 V when the motor runs at 2900 r/min. commutator bars: turns per coil: Armature resistance at 20°C: 0.34 2. on P I Sign Extract Text I Share 1/1 More
A 250 V, 4-pole, wave-wound d.c. series motor has 782 conductors on its armature. It has armature and series field resistance of 0.75 ohm. The motor takes a current of 40 A. Estimate its speed and gross torque developed if it has a flux per pole of 25 mWb.
Left hand rule may be applied to an AC generator to find out: Select one: a. direction of rotor rotation b. direction of magnetic field c. direction of induced emf d. direction of induced torque
A 20-kW 220-volt shunt generator has an armature resistance of 0.07 ohm and a shunt resistance of 200 ohms.Determine the shunt field current A. 0.1 A B. 1.1 A C 2.1 A D. None of these
A 4 pole lap wound DC shunt motor armature has 600 conductors, if the useful flux per pole is 35mWb, while running it generates the emf of 256 V. What will be the rotor speed of DC motor?
The total conductor of the direct current generator shown in the figure is 1440. The length of the armature is 30cm, the magnetic flux of a pole is 0.8 Tesla and the armature rotates at a speed of 4 m / s. Find the value of the voltage generated by the armature according to the position in the figure.
This course EHide blom Clear my choice An eight-pole, 24 KW, 124 V, DC machine has a duplex LAP-wound armature which has 72 coils with 6 turns per coil. Its rated speed is 3000 RPM. Assume no dead zone Find the constant K and the flux per pole to produce 80 Volts at no-load conditions Select one: a. None Ob. K = 68.86 and flux = 3.33 mWb/pole Oc.K = 68.755 and flux = 3.7 mWb / pole O d. K = 95.5 and flux = 3.7 mWb / pole A peries DC motor has a series-field windino of 25 turns per pole. Its armature resistance in 0,1 2. and its
A six-pole dc machine has an armature connected as a lap winding. The armature has 32 slots with six conductors per slot. The armature is rotated at 600 rpm, and the flux per pole is 30 mWb. Calculate the induced voltage. 1
A 6-pole, 1750 rpm shunt motor has a lap wound armature with 580 conductors. If the flux per pole is 15 milli weber, what horsepower is developed for a normal armature current of 350 amperes?
A DC series motor having a resistance of 0.4 ꭥ and runs at 2000 rpm when connected to 250 V supply and drawing a current of 20 A. (i) What resistance must be added in order to limit the speed to 4000 rpm when armature current is 5A? Assume flux varies linearly. (ii) What resistance must be added to limit the speed to 1000 rpm when armature current is 30 A? Assume that the flux at 30 A is 20% more than that at 20A. (iii) At what speed the motor will run if it is connected directly to 250 V supply when the load is such that the current drawn is 30 A?
4. What for brushes are employed in DC generator? 5. What is the function of armature in a DC generator? 6. What is the function of commutator in a DC machine in generator action. 7 Whieh diffe u0ad in