Q 4: A 300 L/s of water flow through pipe Shown in figure (4). The pressure at entrance is 70 KPa. Calculate the force by fluid of sp.gr-0.9 on the bend if the volume of bend is 0.085 m³. (R= 8.55 KN) D₁= 30cm = D₂=20cm 60 Q4 1.5

Q 4: A 300 L/s of water flow through pipe Shown in figure (4). The pressure at entrance is 70 KPa. Calculate the force by fluid of sp.gr-0.9 on the bend if the volume of bend is 0.085 m³. (R= 8.55 KN) D₁= 30cm = D₂=20cm 60 Q4 1.5

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4) A constriction in a pipe will cause the velocity to rise and the pressure to fall at section 2 in the throat. The pressure difference is a measure of the flow rate through the pipe. The smoothly necked-down system shown in Figure is called a venturi tube. Find an expression for the mass flux in the tube as a function of the pressure change. (1) HGL 4²² (2)
Question 1: Water is expelled by a jet to the environment (i.e. the water flow is surrounded by atmospheric pressure). To change the direction of the water flow, this enters to a curved pipe as show in the figure (top view perspective). Calculate the forces exerted by the flow to the pipe in x and y direction (both horizontal). Use a water density of 1000 kg/m³, Q=1 m³/s, diameter d-0.3 m. Follow the 4 steps explained in the lectures and state your assumptions clearly. 30 Question 2: Repeat question 1 but change the curvature from 30 degrees to 90 degrees. How the forces change? 90
Q2) Several water pipes intersect at the junction box illustrated in Figure. Determine the force required to keep the junction box in place. Assume water at 4°C. 250 mm Q₁ = 0.2 m³/s P₁ = 480 kPa 350 mm 300 mm QIVA = 0.3 m³/s /P = 400 kPa 30° Q=0.1 m³/s Pc = 450 kPa 50⁰ 200 mm 60° Q = 0.4 m³/s PD = 350 kPa
Problem Consider a cylindrical pipe of length L and diameter D = 2R. The angle that the axis of the pipe forms with the vertical direction is a. Assume that when the fluid enters the pipe its velocity is uniform (i.e., it has the same value over the entire cross-section of the pipe) and equal to U in the axial direction. In the radial and angular directions, the velocity is zero. So, it is: 2 =0: v(r, 0, 2) = Ue, (1.1) Here v is the fluid velocity and e, is a vector of unit magnitude parallel to the coordinate axis z; furthermore, we have assumed that the pipe inlet is located at z = 0. Near the entrance of the pipe, the velocity profile varies in the axial direction. But after a certain entrance length, the profile becomes fully developed, no longer changing with z. The evolution of the velocity profile is sketched in Fig. 1, where, for clarity, the pipe inclination is not shown. The entrance length is denoted by L.. For z > L., the fluid velocity is no longer a function of the axial…
This very large reducing bend is in a vertical plane. Water is flowing. Diameter at 1 is 6 ft., diameter at 2 is 4 ft,, discharge Q is 300 cfs, and pressure at 1 is 40 psi. Neglect headloss. a) Find p2 in psi, and b) Find Fx, the force (vector) of the pipe bend on the water, x direction only: This is an energy and momentum problem. only HANDWRITTEN answer needed ( NOT TYPED)
2500kW power is generated shown in the Figure with a water flowrate of 20 m3/s. The head loss for the entire flow is 2.5m. (a) Find the pressure difference P1 - P2 across the turbine. (b) Find h You can neglect the head loss between point 1 and 2.
Q6: The U-bend in the figure below is connected to a flow system by flexible hoses that transmit no force. The pipe has an ID of 3 in. Water is flowing through the pipe at a rate of 600 gal/min and density is 1000 kg/m³. The pressure at point 1 to 5 psig and at point 2 is 3 psig. What is the vertical component of the force in the support? Neglect the weight of the pipe and fluid. Flow FIGURE Vertical pipe U-bend. Flex hoses Support
Find the horizontal and vertical forces to hold stationary the nozzle shown in the figure below. The fluid flowing through it is 10 °C liquid water; A₁ = 1.2 m², A₂ = 0.300 m², V₁ = 15 m/s, p2 = Patm and p₁ = Patm + 75 kPa. Neglect effects of gravity. Fx= i Fy= i A1 P1 KN kN Fy ZA A2, P2 = Patm Fx 45° Patm
Water is stored in a tank sketched in the figure below to support the demand of a nearby community area.The system is designed so that pressure at the location B always lies in the range of 330 to 440 kPa (gauge).Water demand fluctuates between 0.3 and 1 m3/s regardless of pressure at B. The supply pipe of 600 mmdiameter and 1 km length between A and B is made of steel and has the equivalent sand roughness of 1 mm.Although not shown in the figure, the supply pipe has five 90◦ bends, each having the head loss coefficientof 0.8. The figure shows that the bottom end of the tank is located 42 m above the ground, and the pipe isburied 1.5 m below the ground. A pump system regulates so that the tank keeps the same water level all thetime. Assume water at 20◦C, and air in the storage tank has the atmospheric pressure. To meet the designcriterion for pressure at B, what should be the depth of water h in the storage tank?
P1 = Patm 1 V 7.3 m/s %3D Flow h = 0.96 ft water 3 Density of water 1000 kg/m Determine the pressure at the point 3?
4: Water flow through a pipe at 5L/s as shown in figure. If gage pressure of 12.5kPa, 11.5kPa and 10.3kPa are measured for P1, P2 and P3 respectively, what are the head losses between 1, 2, and 3? (2) -- 50 mm - 50 mm 10m O Pa d, - 30 mm
Problem 4.35 4-35 Water flows steadily through a pipe of length L and radius R=75 mm. Calculate the uniform inlet velocity, U, if the velocity distribution across the outlet is given by 14 = Ugan and M-3 m/s. R² R [Difficulty: 2]