Water (p 1.96- slug) flows through the pipe system below. Data is given below:=ft³Pipe 1: V₁=1.8 ft, D₁ =2.4 inches, p₁ =24.9 psiPipe 2: V₂=1.4 t, D₂=1.9 inches2Pipe 3: D3=0.7 inchesAssume no energy is lost to friction.Find the pressure p3. Report your answer in psi.V₂V₁P₁D₁D₂P2D3₁V3P3

Answered: Image /qna-images/answer/2b802679-27c8-46f5-ab8f-8f8478459b73.jpg

slug ) flows through the pipe system below. Data is given below: ft³ Pipe 1: V₁=1.8 ft, D₁=2.4 inches, p₁ =24.9 psi Pipe 2: V₂=1.4 - , D₂=1.9 inches 2 S Pipe 3: D3=0.7 inches Assume no energy is lost to friction. Find the pressure p3. Report your answer in psi. V₂ Water (p= = 1.96- V₁ P₁ D₁₁ D₂ P2 D3 V3 p3

slug ) flows through the pipe system below. Data is given below: ft³ Pipe 1: V₁=1.8 ft, D₁=2.4 inches, p₁ =24.9 psi Pipe 2: V₂=1.4 - , D₂=1.9 inches 2 S Pipe 3: D3=0.7 inches Assume no energy is lost to friction. Find the pressure p3. Report your answer in psi. V₂ Water (p= = 1.96- V₁ P₁ D₁₁ D₂ P2 D3 V3 p3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Use g=32.2 */sec2 (9.81 m/s2) and 60°F (16°C) water unless told to do otherwise.• Google schedule-40 pipe’s thickness at different nominal size to obtain the innerdiameter of the pipe for accurate determinaLon of flow velocity.• Must show your work to support your selecLon. Otherwise, no points will be given.Water flows through a schedule-40 pipe that changes gradually in diameter from 6 in (154mm) at point A to 18 in (429 mm) at point B. The volumetric flow rate is 5.0 *3/sec (130 L/s). The respecLve pressures at points A and B are 10 psia (70 kPa) and 7 psia (48.3 kPa). All lossesare insignificant. What are the direcLon of flow and velocity at point A? (A) 3.2 */sec (1 m/s); from A to B(B) 25 */sec (7.0 m/s); from A to B(C) 3.2 */sec (1 m/s); from B to A(D) 25 */sec (7.5 m/s); from A to B
Please help me with this problem clearly. List two sources of error in the water-filled tube and pressure gauge method of measuring head for a hydro system and how to avoid them. Using this method, a series of measurements up a hill to the source of the stream produces the following heights: 1.5m, 0.7m, 1.0m, 1.9m, 1.6m, 0.3m, and 0.8m. What is the total head for this site? If the flow rate was 0.5 m3s-1, calculate the power available in this stream?
Q1) Using a system similar to that shown in figure, compute the required air pressure above the water to cause the jet to rise h2 = 41 m from the nozzle. The depth h, -2.1 m. Air pressure
Don't give wrong answer please
Water flows from a 20-mm-diameter pipe with a flowrate Q as shown in the figure below. What is the approximate diameter of the water stream, d, in units of cm, if the distance below the faucet is, h=2 m, and Q = 0.003 m³ /s? 20 mm O a. 1.83 m b. 2.07 m O c. 3.29 m d. 4.66 m O e. 5.29 m
None
%3D Find the pressure in KN/m2 at the center of pipe A. T = 10°C. Oil (S = 0.85) Water 90 cm 150 cm Water 30 cm Mercury (S = 13.6) to 30 cm
show dolution and diagrams.
Flow Through Pipes A pipe 800 m long connects two reservoirs whose level difference is 60 m. Find the discharge in pipe in Liters/sec, if diameter of pipe is 0.5 m Take all losses into account. Assume f = 0.01.
3. A seamless steel pipe carries 2000 m³ of steam per hour at a pressure of 1.2 N/mm². The velocity of flow is 28 m/s. Assuming the tensile stress as 40 MPa, find the inside diameter of the pipe and its wall thickness. [Ans. 160 mm; 5.4 mm] 4. Compute the dimensions of a flanged cast iron pipe 200 mm in diameter to carry a pressure of 0.7 N/mm².
1-A steel discharge pipe with a roughness equal to 0.5 mm is 800 m long and pumps 265 m³ of water per hour at a temperature of 20°C. The pipe diameter is 25 cm. Calculate the head loss. Data: kinematic water viscosity equal to 10-6 NOTE: if necessary, use Moody's DiagramHelp?