Q3b. Draw and explain the phase diagram of sulfur system. At 200 °C, the specific volume of water and steam are respectively 1 c.c. and 1673 c.c. Calculate the change in vapour pressure of the system by 20 °C change in temperature. The molar heat of vaporization of water in this range may be taken as 9.70 K cal.

Q3b. Draw and explain the phase diagram of sulfur system. At 200 °C, the specific volume of water and steam are respectively 1 c.c. and 1673 c.c. Calculate the change in vapour pressure of the system by 20 °C change in temperature. The molar heat of vaporization of water in this range may be taken as 9.70 K cal.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Vapour Pressure vs 1/T - DeltaHvap - Clausius Clapeyron Equation The standard enthalpy of vaporization (H°vap) of acetone ((CH3)2CO) is 32.0 kJ/mol. The normal boiling point of acetone is 56.5°C. Calculate the vapour pressure of acetone at 33.5°C.
A volume of 7.32 L of air is bubbled through liquid toluene at 360. K, thus reducing the mass of toluene in the beaker by 11.2 g. Assuming that the air emerging from the beaker is saturated with toluene, determine the vapor pressure of toluene at this temperature.
The normal boiling point of cyclohexane is 80.74 °C.At 20.00 °C, the vapour pressure of cyclohexane is 0.1026 atm.What is the vapour pressure of cyclohexane when the temperature is 33.00 °C? ----------------------------------------------------------------------------------- The vapour pressure at the normal boiling point is known, by definition, to be 1 atm.You therefore can write three different equations of the sort:lnPvap = [(−∆H)/(RT)] + Ci.e. for each of the three pairs of P and T.You can take the difference between the equations for the cases (Pb, Tb) and (P1, T1).This could be used to solve for [(−∆H)/(R)].Analogously you can take the difference between the equations for the cases (Pb, Tb) and(P2, T2).Since both differances must give rise to the same value for [(−∆H)/(R)], you can equate them to write an equation which allows you to calculate P2 in terms of Pb, Tb, P1, T1 and T2
From the following vapor pressure data for ethyl amine, an estimate of the molar heat of vaporization of C₂H5NH₂ is | kJ/mol. P, mm Hg T, K 40.0 233 100. 248
Microemulsions have an extremely high interfacial area between the two phases. Explain how this property contributes to their spontaneous formation when the appropriate combination of components are combined.
Acetone has a vapour pressure of 53.3 kPa at 39.5 °C and 202.6 kPa at 78.6 °C. Estimate the acetone's critical pressure by knowing that Te is 234.95 °C. 1414 kPa 2414 kPa 5414 kPa 6414 kPa
None
5.The diagram below is an example of Two Partially Miscible Liquids (T vs Mole Fraction).Fill out the question marks with correct number of degrees of freedom. Material Equilibrium: 2 Partially Miscible Liquids At constant P: T= T • 2 components ( Liquids A and B) • p phases (liquid, gas) • No reactions • No ions / electrolytes Concentration is not specified T Number of independent components, Cing = c -r-a = 2 F=? F=? Fm? F=? T = T F=? Thus, T = Tuc F = Cind -p+ 2 F= 2-p+1 F=? F= 3-p ZA
Hexane and heptane form nearly ideal solutions. The boiling point of pure hexane is 69.0°C. Calculate the vapour pressure of hexane in a solution of x hexane = 0.60 If the activity coefficient of hexane in this solution were actually 0.95 rather than 1.00. a. 433 torr b. 361 torr c. 500 torr d. 760 torr