8. The diagram below is an example of Liquid-Solid-Temperature CompositionPhase Diagram of Partially Miscible Solids.The left vertical line is B rich while theright vertical line is A-rich.Define the phases present in the region A to F.LS – TZ Phase Diagram: Partially Miscible SolidsT= TmThis type of mixture is for partiallymiscible solidsAt the solid region:• The B- rich region, or the ß phase T• The A- rich region, or the a phaseAt each single solid- phaseregion, there are 2 different formsof the solid solution.T = TT = TeuLever Rule applies to all 2– phaseregions.EZa

8. The diagram below is an example of Liquid-Solid-Temperature Composition Phase Diagram of Partially Miscible Solids.The left vertical line is B rich while the right vertical line is A-rich.Define the phases present in the region A to F.

8. The diagram below is an example of Liquid-Solid-Temperature Composition Phase Diagram of Partially Miscible Solids.The left vertical line is B rich while the right vertical line is A-rich.Define the phases present in the region A to F.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Answer the following questions based on the phase diagram provided. P/MPa 0.1 6.1 68.3 240.85 T/°C a) Is this phase diagram for benzene? Provide at least three pieces of evidence. b) Determine the enthalpy of vapourization for the substance in this phase diagram. c) Use the information provided to determine the equilibrium pressure of 10 mol of this substance in a 100 L container at 100 °C.
(f) There are 7 crystal systems, 2 of them are predominant in metals, which are the two?
Naphthalene (C10H8) is a solid at room temperature and 100 kPa. At 100 kPa it melts at 80.2 oC. The melting point increases by 2.32 oC when the pressure is increased to 104kPa. Naphthalene boils at 219 oC, at atmospheric pressure. The vapour pressure of naphthalene at 201 oC is 67.0 kPa. The triple point of naphthalene is at 80°C and 2.1 kPa. Use this data to construct a ln(p)-T phase diagram for naphthalene and label all the regions of your diagram (you do not need to draw the diagram to scale). Please draw this diagram.
The vapor pressure, P, of a certain liquid was measured at two temperatures, T. The data is shown in the table. Т К) Р (КРа) 275 3.65 775 7.14 Keep the pressure units in kilopascals. If you were going to graphically determine the enthalpy of vaporizaton, AHvap, for this liquid, what points would you plot? To avoid rounding errors, use three significant figures in the x-values and four significant figures in the y-values. point 1: x = point 1: y = point 2: x = point 2: y = Determine the rise, run, and slope of the line formed by these points.
Determine the enthalpy of vaporization for this substance.ΔHvap =
Identify the phase diagram, and explain the curve OB, OA and OC. Also, in case of reduced phase rule, out of the three variable only pressure is kept constant compared A to concentration or temperature. Why? Temperature Pressure
The vapour pressure of a substance describes how readily molecules at the surface of the substance enter the gaseous phase. At the boiling point of a liquid, the liquid's vapour pressure is equal to or greater than the atmospheric pressure exerted on the surface of the liquid. Since the atmospheric pressure at higher elevations is lower than at sea level, the boiling point of water decreases as the elevation increases. The atmospheric pressure at sea level is 760 mmHg. This pressure decreases by 6.50 mmHg for every 100 m increase in elevation. Part A What is the boiling point of water at an elevation of 7600 m ? Express your answer with the appropriate units using three significant figures. Elevation Pressure • View Available Hint(s) 760 mmHg 1000 m 695 mmHg HA 2000 m 630 mmHg The boiling point of water decreases 0.05 °C for every 1 mmHg drop in atmospheric pressure. T = 75.30 Enter your answer using units of temperature. No credit lost. Try again.
Question 8 Which of the following phase diagrams corresponds to a system wherein boiling occurs before the two liquids are fully miscible? TIK |210 Composition of one chane P.1 Vapour P.2 292 290 P.2 Compostion of second phase uid. P= 2 Liquia 273 Liquid P.1 Liquid, P- 2 Mole fraction of B, Mole fraction of B. B D E ОЕ O A D O B ооос о Temperature, T
A volume of 7.32 L of air is bubbled through liquid toluene at 360. K, thus reducing the mass of toluene in the beaker by 11.2 g. Assuming that the air emerging from the beaker is saturated with toluene, determine the vapor pressure of toluene at this temperature.
AH vap In(Pvap) R The following graph was obtained for a pure volatile liquid substance. In(Pvap) 4 3 2 -1 -2 -3 -4 == ²( ) + C 0.002 (Note that Pvap is the vapour pressure in atm.) 1/T (K-¹) Determine the enthalpy of vaporization for this substance. Hvap 0.003
Calculate the total pressure in a binary system where the mole fraction of A in the vaporphase is 0.200, the vapor pressure of pure A is 100. mmHg and the vapor pressure ofpure B is 300. mmHg.
2. Refer to the phase diagram depicted below: if a sample is made by mixing 3 moles of A and 7 moles of B at 50oC, identify the phases exist in the system: one phase: vapor one phase: liquid two phases: vapor and liquid two phases: two liquid