Q3(): The pin B supports the 6 ft Load W= 9000 lb and connects horizontal cable with point A. If the pin C is subjected to double shear W 9 ft while pin at B is a single shear. The diameter of pin C is 1.5 in while the diameter of pin B is 0.8 in. Determine the shear stress at pins B and C. Also find the stress in the cable AB if its diameter is 0.5 in

Q3(): The pin B supports the 6 ft Load W= 9000 lb and connects horizontal cable with point A. If the pin C is subjected to double shear W 9 ft while pin at B is a single shear. The diameter of pin C is 1.5 in while the diameter of pin B is 0.8 in. Determine the shear stress at pins B and C. Also find the stress in the cable AB if its diameter is 0.5 in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two cables are tied together at C and are loaded as shown. Knowing that P = 500 N and angle alpha is 50 degrees, determine the tension in cable AC.
A 2.0 kN bar AB carries a load F = 75 kN vertical force at A. The baris supported by a pin at B and the 12.5-mm. diameter cable CD. Find the a.tension in the cable CD in kN.b.Horizontal reaction at B in kN.c.Vertical reaction at B in kN.d.Tensile stress in the cable in MPa.e.Shearing stress at B in MPa.
Please solve
solve for the tension at cable AB and the reaction at E, considering the weight of bent bar CBDE = 420 lb *pls use 3 decimal places all throughout the solution
In the cable structure below, when the maximum moment of column BF Mmax =1500KN-m and P1 =2P2, calculate the maximum value of P1. = 2m E! P2 C hp 6m 3m D A 5m 5m 5m
2. A cable 300 m long weigh5 600 N. The tension at the emds of the cable are 400 N and 446 N, respectively. (Note: Treat this as catenary). a) Determine the difference in elevation of the supports at both ends. b) Determine the difference in elevation of the lowest point and the lower support. c) Compute the horizontal span of the cable. T= 446 N Tz= 400 N S2 X2 L
The cable AB prevents bar OA from rotating clockwise about the pivot O. If the cable tension is 600 N, determine the n- and t- components of this force acting on point A of the bar. n A 2.1 m B Answers: Tn= i g Tt= IN 1.4 m 0 55° N N
the parabolic cable shown carries a uniform load of 120 kN/m. the lowest point of the cable is located vertically 3m from the left support and 6m from the right support. if the length of the cable is 100m A.) Determine the lowest point in meters, of the cable measured horizontally from the left support. B. ) determine the value of the minimum tensile force in kN, that the cable can withstand C.) determine the value of the maximum tensile force in kN, that the cable can withstand
5. The tension in cable BC is 100 lbs. Determine the reactions at the fixed support. Note that the L-shaped bar has an applied load of 200 lbs and an applied couple of 300 ft-lbs. B 200 lb -3 3 ft-3 ft- -6 ft- C 6 ft 300 ft-lb
a water supply crossing a wide river is to be supported by a flexible wire cable with an allowable tensile of 20000kg. the pipe weight 50 kg per meter and has a total length of 60m. a. determine the minimum sag of the cable b. determine the tension the lowest point of the cable. c. if the sag is to be 2m. what is the tension at the support?
THE CABLE ABCD IS HELD IN THE POSITION SHOWN BY THE HORIZONTAL FORCE P. DETERMINE P AND THE FORCE IN EACH SEGMENT OF THE CABLE. 1.0 m D A-2 m 3 m |3 m 4 m 15 kg 25 kg B.
Q.1 The rigid beam is supported a pin connection at A and a cable BD at point the. Diameter of pin 3x at A is 20mm and Diameter of cable BD is 30mm. D P 15 (kN) x-2.7(m) 4х 4x Calculate the followings a) Support reactions at A and the axial force in Cable BD. b) Find the axial stress in cable BD and shear stress at pin A in the case of Double shear at A. c) Calculate the deformation and final length of BD if the modulus of elasticity E=200GPA d) Calculate the change in diameter of BD if the Poisson ratio v-0.3. |