Q.1 The rigid beam is supported a pin connection at A and a cable BD at point the. Diameter of pin at A is 20mm and Diameter of 3x cable BD is 30mm. D P- 15 (KN) x=2.7(m) 4x 4x Calculate the followings a) Support reactions at A and the axial force in Cable BD. b) Find the axial stress in cable BD and shear stress at pin A in the case of Double shear at A. c) Calculate the deformation and final length of BD if the modulus of elasticity E=200GPA d) Calculate the change in diameter of BD if the Poisson ratio v-0.3.

Q.1 The rigid beam is supported a pin connection at A and a cable BD at point the. Diameter of pin at A is 20mm and Diameter of 3x cable BD is 30mm. D P- 15 (KN) x=2.7(m) 4x 4x Calculate the followings a) Support reactions at A and the axial force in Cable BD. b) Find the axial stress in cable BD and shear stress at pin A in the case of Double shear at A. c) Calculate the deformation and final length of BD if the modulus of elasticity E=200GPA d) Calculate the change in diameter of BD if the Poisson ratio v-0.3.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1. In the structure below, members BF and AE are connected with a pin at D. Find the minimum…

Q: For the truss shown in the figure: 20KN a) Find the support reactions. b) By inspection, identify…

A: Step 1

Q: ecause the cable passes over a small pulley at B, the tension may be as he cable. Assume a = 3 in. A…

Q: A cylindrical pin made of carbon steel is loaded with a maximum possible twisting moment Mv. Maximum…

A: G = 80 GPa Maximum shear stress = 40 MPa Determine the free end distortion in degree.

Q: Frame ABCDE shown in Figure Q2 is supported by a fixed connection at B, roller at D and pinned at A.…

A: Solution:Solve using Moment distribution method:(a)Distribution Factor:JointMemberRelative…

Q: 5. Bar ABD and bar CEF are connected using a pin at point C and a strut member BE to support a 9000…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5…

Q: A force P of magnitude 1,100 N is applied to the pedal shown satisfies a shearing stress in the pin…

A: Given data, Applied force P = 1100 N Shear Stress in the pin = 42 MPa We have to determine the…

Q: Container W weighs 376 N. It is suspended from ring A. Cable BAC oases through the ring and is…

A: W=376 NTo find- Force vector for P and Q

Q: F9-5. The beam is subjected to the load at its end Determine the maximum principal stress at point…

A: Given : Determine the maximum principle stress at point B ? Concept - Principle stresses are taken…

Q: Determine the location e of the shear center, point O, for the thin-walled member having the cross…

A: Given :

Q: Determine the normal stress at A and B in member CD. Pins C and D are at the centroid of the T…

A: Calculating the total area of T-Cross section A: A=(7*1.5)+(6*1) =16.5 in2

Q: Determine the force in member BD for the truss using the method of joints.

Q: ! Required information Each of the four vertical links has an 8 x 36-mm uniform rectangular cross…

A: Given data - Cross section = 8×36 mm Diameter of Pin = 16 mm P = 23 KN Find out - Average shear…

Q: 4. Select member FC and CB in the truss to carry the inclined force P. Set the allowable tensile…

Q: The bridge truss shown carries the following uniform live load and concentrated live load. в с DE A…

A: Solution: Given: h = 3 m B = 8 m ULL = 15 PLL = 110

Q: The rigid element BCD is supported by a bar AB with a diameter of 25 mm and a connection at C with a…

A: Given Load 50 and 15 kNDiameter 25 and 10 mmTo find out Normal stressShear stress

Concept explainers

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.

Question

Q.1
The rigid beam is supported a
pin connection at A and a cable
BD at point the. Diameter of pin
3x
at A is 20mm and Diameter of
cable BD is 30mm.
D
P 15 (kN) x-2.7(m)
4х
4x
Calculate the followings
a) Support reactions at A and the axial force in Cable BD.
b) Find the axial stress in cable BD and shear stress at pin A in the case of Double
shear at A.
c) Calculate the deformation and final length of BD if the modulus of elasticity
E=200GPA
d) Calculate the change in diameter of BD if the Poisson ratio v-0.3. |

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. All members of the truss A B C shown have a cross- sectional area of 500 mm? and all pins have a diameter of 20mm. Determine: 2 m (a) The axial stresses in members BC and DE F E D -2 m 2 m 2 m- (b) The shear stresses in the pin at A, assuming the pin is in double shear P = 21 kN
3. Determine the required diameter of the pins at A and B to the nearest 1mm if the allowable shear stress for the material is T= 300 MPa. Pin A is subjected to doble shear, whereas pin B is subjected to single shear. A 1.5 m B 1.5 m C D 30 kN 2.25m
The bar is snugly fit between points C and A before the loading is applied at Collar B. Assume E = 200 GPa for the steel. The circular bars in the assembly are solid. The bars are solid with a diameter of 15 mm. Assume a fixed rigid support at C and A. A C В 6 kN 3 m 2 m A) Show the FBD and compatibility equation for this problem. B) Determine the support reactions at A and C. (Horizontal forces only) Left side: Fc = Right side: FA =
The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with the thickness shown in the figure. The working stresses are 70MPa for shear in the rivets and 140MPa for bearing stress due to the rivets. How many 22mm diameter rivets are required to fasten the following members to the gusset plate: (a) BC; and (b) BE? 000 4 m B с 96 kN D 6 m E 200 KN 4 m F G 4 m 96 kN H to- PBC - -14-mm-thick gusset plate -13-mm-thick angle 6-mm-thick angle PBE