1. In the structure below, members BF and AE are connected with a pin at D. Find the minimum diameter (rounded to the nearest 1/16 of an inch) that limits the shear stress to 7200 psi for the pin at D. F Smooth A 870 lb ↓e C -3 ft → 4.5 ft D 600 lb 2 ft -3 ft → B E 2 ft 7 ft

1. In the structure below, members BF and AE are connected with a pin at D. Find the minimum diameter (rounded to the nearest 1/16 of an inch) that limits the shear stress to 7200 psi for the pin at D. F Smooth A 870 lb ↓e C -3 ft → 4.5 ft D 600 lb 2 ft -3 ft → B E 2 ft 7 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The two vertical steel [E = 200 GPa] rods that support rigid bar ABCD are initially free of stress. Rod (1) has an area of A₁ = 350 mm² and a length of L₁ = 2.1 m. Rod (2) has an area of A₂ = 375 mm² and a length of L₂ = 1.5 m. Assume dimensions of a = 3.2 m, b = 1.1 m, and c = 1.4 m. After a load of P = 130 kN is applied to the rigid bar at D, determine: (a) the normal stresses in rods (1) and (2) (b) the magnitude of the downward deflection of the rigid bar at D. y,v (2) a L2 Rigid bar L₁ Answer: (a) σ₁ = i 02= i (b) VD= i (1) B MPa MPa mm -X,U b C ↓ С D P
Determine the magnitude of the pin force at A. Assume W = 800 lb, a = 4.3 ft, b = 3.2 ft, r= 8 in. B W D Answer: A = i Ib
В A B C The system above is comprised of two-force members AB and AC, supporting a vertical force at point A. Assuming the system is drawn to scale and is in equilibrium, which of the following best describes the nature of the forces in members AB and AC? a) AB is in tension AC is in compression b) AB is in compression AC is in compression c) AB is in tension AC is in tension d) AB is in compression AC is in tension
The two vertical steel [E = 200 GPa] rods that support rigid bar ABCD are initially free of stress. Rod (1) has an area of A1 = 410 mm2 and a length of L1 = 3.2 m. Rod (2) has an area of A2 = 355 mm2 and a length of L2 = 1.3 m. Assume dimensions of a = 3.4 m, b = 1.2 m, and c = 1.5 m. After a load of P = 50 kN is applied to the rigid bar at D, determine: (a) the normal stresses in rods (1) and (2) (b) the magnitude of the downward deflection of the rigid bar at D. y,v (2) L2 a B C D x,u Rigid bar |(1) Answer: (a) o1 = i MPa 02 = i MPa (b) VD = i mm
A bridge girder AB on a simple span of length L = 20 m supports a distributed load of maximum intensity q at midspan and minimum intensity g/2 at supports A and B that includes the weight of the girder (see figure). The girder is constructed of three plates welded to form the cross section shown. 500 mm L= 20 m 18 mm 1600 mm 500 mm (a) Determine the maximum permissible load q based upon an allowable bending stress oallow = 130 MPa. Round to the nearest tenth. kN Gmax = (b) Determine the maximum permissible load q based upon an allowable shear stresS Tallow = 55 MPa. Round to the nearest tenth. kN Gmax m
Problem # 4. A 12-mm-diameter steel E 200 GPa] rod (2) is connected to a 30mm wide by 8 mm thick rectangular aluminum [E 70 GPa] bar (1), as shown. required to Determine the force P stretch the assembly 10.0 mm. Ans: = A (1) 0.45 m B (2) 1.30 m - C
A homogeneous bar AB weighs 900 lb. Calculate the reactions at supports A and B.
15
Radius of the pin at C is 3mm. While at static equilibrium, we know that a force P of magnitude 500 N is applied to the pedal shown, calculate (a) The average shearing stress in the pin at C (b) the corresponding bearing stress in the pedal at C, (c) the corresponding bearing stress in each support bracket at C. 9 mm T 5 mm C A 75 mm 125 mm B 300 mm PI D
Subject: Static of rigid bodies Find: Shear Diagram of beam 1, 2, and 3. Show me the solution pls thank you!