The cable AB prevents bar OA from rotating clockwise about the pivot O. If the cable tension is 600 N, determine the n- and t- components of this force acting on point A of the bar. 12 j 2.1 m 0 55° B Answers: Tn= i T₁= i 1.4 m N N

The cable AB prevents bar OA from rotating clockwise about the pivot O. If the cable tension is 600 N, determine the n- and t- components of this force acting on point A of the bar. 12 j 2.1 m 0 55° B Answers: Tn= i T₁= i 1.4 m N N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 2) The truss is carrying two masses m (mg=100 N). It is supported by a rope at A and pin support at…

Q: Thebent rod is supported by a ball-and-socket joint at O, a cable at B, and a slider bearing at D.…

A: Calculating different vectors and their directions:

Q: The frame ABCD in figure 6, has two cables tied at B, BG and BH. If the tension in cable BG is 1000N…

A: FBG = 1000 N FBH = 1500 N Find: (a) The moment about A of the force exerted at point B by both…

Q: What is the x component of the reaction |(lb) (exerted on the boom by the wall) at C. A? What is the…

A: Given:- The Boom AC has a negligible weight The boom is supported by the cable D & E and…

Q: Three cables are connected at A, where the forces P and Q are applied as shown. Determine the…

Q: ring at B. Khowing tens: le is 385 N, determine the components of the force e cable on the support…

A: According to given data in the figure below

Q: Cable OA is used to support column OB and exerts a force of 9 kN on the column at O: (a) Determine…

A: Given: a= 5m, b = 3m, c=9m Required : Angle between OA and OC length AC projected component of 9KN…

Q: For the cable assembly presented, the member ABC is assumed to be rigid and is pinned at A. Also, it…

Q: Q.4) Rod AB is in the x-y plane and supported by two cables as shown. The tension in cable AC is 910…

Q: T 3) The weight of the unit length of the homogeneous cable in the figure is given as w. and since…

Q: *5-88. Determine the horizontal and vertical components of reaction at the pin A and the force in…

Q: The cable AB carries a tension of 470 N. Determine the moment about O (positive if counterclockwise,…

Q: A T 10 ft -25 ft- B Wo 15 ft

Q: The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB…

A: Given: TAB = 9.3 KN , a= 31m, b= 37m, c= 25m, d= 31m Find: TAC= ? , R=?

Q: The cable AB prevents bar OA from rotating clockwise about the pivot O. If the cable tension is 900…

Q: Rod AB is secured with a cable at point B and a smooth, up and down movable collar from point A.…

Q: 20° B 50 D 55° VQ

A: To find the force in cable TDE and Q -

Q: 3. If the plate is to remain in equilibrium, find the tension for all the three cable that supports…

A: Consider the following free body diagram:

Q: 4) The cable shown in the figure is subjected to the forces P, and Q. 4-a) Determine the support…

A: step 1-

Q: 3 m P 3 m B 1.5 mi 3 m E 3 m 1.5 m

Q: Cable AB is supported by a truss structure at A and a pin at B. A uniform distributed load is…

Q: over the large pulley. A locking pin at A prevents rotation of the pulley. If µ = 0.4 between the…

Q: 6 KN 53 3m * 5m Find the tension on the cable Find the reaction at c Find the stress in the cable of…

Q: Weight W is supported by spring OC, which is attached to two cables at O. The un-stretched length of…

Q: 2.123 A container of weight Wis suspended from ring A. Cable BAC passes through the ring and is…

A: Given: W = 270 lb The tension is the same in both portions of cable BAC. Solution: Free body…

Q: A to C. WALL B 6 m WALL D 2 m 4 m 6 m 12 kN y A 3 m 3 т 5 т 5 т 25 kN

Q: the uniform concrete pole has a mass of 25 tons and is slowly being lifted to a vertical position…

A: Reference : Engineering Mechanics, Tension in cable. Given : Mass = 25 tons = 25000 kg A force P…

Q: The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by…

Q: Cable AB is supported by a truss structure at A and a pin at B. A uniform distributed load is…

Q: A 30 kg mass M is held in place by the 50 N force F1, cable OA and cable Find the mass m of the…

A: Given : Mass M = 30 kg Force F1 = 50 N To Find : The mass m of counterweight to keep point O in…

Q: 14 ft 6 ft K 16 ft F |G H B Q L he cable shown above is loaded with P 5 k and Q = 4 k. L = 4 @ 12 ft…

Q: Cable El is used to support the bascule bridge at E. The weight of the deck gives result to the…

Q: Cable AB is supported by a truss structure at A and a pin at B. A uniform distributed load is…

A: 50

Q: the uniform concrete pole has a mass of 25 tons and is slowly being lifted to a vertical position…

Q: The 1635-lb uniform plate ABCD can rotate freely about the hinge AB. The plate is supported by the…

A: The weight of the plate will be concentrated at the centroid. Since the plate is symmetrical, the…

Q: The cable AB carries a uniformly varying load. It is connected to a wall at A and is held in…

Q: Don't use chat gpt Chatgpt means downvote

Q: SQ1. The bars AB and BC are joined by a pin at A and a horizontal cable. The vertical cable carrying…

A: Free Body Diagram:- tan30 = AB5 AB = 2.887 m sin 30 = xAB x=2.887*sin30 x=1.4435m sin30=y3 y=1.5m…

Q: The cable AB prevents bar OA from rotating clockwise about the pivot O. If the cable tension is 640…

Q: the st icture shown below (CD is a cable) За

A: Take moment about B :∑ MB=0TDC332+421+951+30112=0TDC=-183.333kNso,∑ Fy=0By+TDC35+301+95=0By=15kN↓∑…

Q: The turnbuckle is turned until the tension in the cable AB reaches the value represented by 70 kN.…

Q: From the given cable shown. Use the general cable theorem. P is in kips. Let P = 10 24' 24' D. 5@20=…

Q: Problem III. A cable was used to dry the clothes from wet laundry by hanging as shown below. The…

Concept explainers

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.

Question

The cable AB prevents bar OA from rotating clockwise about the pivot O. If the cable tension is 600 N, determine the n- and t-
components of this force acting on point A of the bar.
n
A
2.1 m
B
Answers:
Tn=
i
g
Tt=
IN
1.4 m
0
55°
N
N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The ball D has a mass of 30kg. If a force F= 120N is applied horizontally to the ring at A, determine the largest dimension d so that the force in cable AC is zero.
2, The rigid body ABC is held in place by ball and socket joints at A and C, and cable DE which passes through the right at point B. Find the tension in Cable DE. The coordinates of the points in (mm) are as follow: A, (0,0,600) B, (600,0,600) C, (800,0,0) D, (0,500,300) E, ( 800,500,0) F, (800,0,600)
4. For the beam and loading shown, determine the tension in the cable and the support reactions at hinge A. Neglect the thickness of the beam and the size and friction of the pulley at E. E 2 kipsft 3 ft 3 ft 2 ft 10 kips 5. Find the maximum weight of the bucket that the wire system can support so that no single wire develops a tension more than 500 N. 3/3 25° 1300 300
3. The cable BC carries a tension of 800 N. Write this tension as a force T acting on point B in terms of the unit vectors i, j, and k. The elbow at A forms a right angle. 0.7 m 1.2 m- 1.6 m 30° B 0.8 m -X
Complete sol. ty
Two cables are tied together at C and are loaded as shown. Knowing that P = 500 N and angle alpha is 50 degrees, determine the tension in cable AC.
Please asap
No. 1 1.12 m 0.96 m 0.98 14 1.28 m 1.20 m steel rod is bent into a semicircular ring of radius 0.96 m and is supported in part by cables BD and BE which are attached to the ring at B. Knowing that the tension in cable BE is 250 N, determine the components of this force exerted by the cable on the support at E.
Q3: A telephone cable is clamped at A to the pole AB. Knowing that the tension in the left-hand portion of the cable is T1 = 800 lb, determine by trigonometry (a) the required tension T2 in the righthand portion if the resultant R of the forces exerted by the cable at A is to be vertical, (b) the corresponding magnitude of R. 25° T₂
Provide free body diagram in solving.
The cable AB prevents bar OA from rotating clockwise about the pivot O. If the cable tension is 720 N, determine the n- and t- components of this force acting on point A of the bar. 4 2.2 m 0 59° 1.9 m Answers: Tn= i T₁ = i N N