The rigid body ABC is held in place by ball and socket joints at A and C, and cable DE which passes through the right at point B. Find the tension in Cable DE. The coordinates of the points in (mm) are as follow: A, (0,0,600) B, (600,0,600) C, (800,0,0) D, (0,500,300) E, ( 800,500,0) F, (800,0,600)

The rigid body ABC is held in place by ball and socket joints at A and C, and cable DE which passes through the right at point B. Find the tension in Cable DE. The coordinates of the points in (mm) are as follow: A, (0,0,600) B, (600,0,600) C, (800,0,0) D, (0,500,300) E, ( 800,500,0) F, (800,0,600)

Architectural Drafting and Design (MindTap Course List)

7th Edition

ISBN:9781285165738

Author:Alan Jefferis, David A. Madsen, David P. Madsen

Publisher:Alan Jefferis, David A. Madsen, David P. Madsen

Chapter7: Construction Procedures

Section: Chapter Questions

Problem 7.4Q

See similar textbooks

Related questions

Q: Member AB is supported by a cable BC and at A by a square rod which fits loosely through the square…

A: Consider the following free body diagram of the square rod:

Q: 2) The truss is carrying two masses m (mg=100 N). It is supported by a rope at A and pin support at…

Q: 1. The beam shown below is supported by a roller, internal hinge at B and fixed at C. Determine the…

A: To Find a. Support reactions at A and B ( here it must be C as there is no support at B. B is an…

Q: The load is supported by the four stainless steel wires that are connected to the rigid elements AB…

A: Given four stainless steel wires that supports load and are connected to the rigid elements AB and…

Q: The truss shown below is pined at A and has a roller at F. The Load applied at E is P=20 kN. The…

Q: Question 1: The truss is subjected to the system of forces as shown in the following figure. The…

Q: The rigid bars AC and BCD are supported by pins at A and B and by a steel rod at D. There is a…

Q: *g. The A-36 steel rod has a diameter of 50 mm and is lightly attached to the rigid supports at A…

A: The diameter of the rod is d = 50 mm. The initial temperature is T1 = 50°C. The second temperature…

Q: ION The truss is acted on by two forces and is supported by a roller at D and a pin support at F. a)…

A: Calculate the support reactions at support D and F…

Q: An assembly of bars are designed in Figure 1: The assembly is made of structural A-36 steel where…

Q: O 300 mm 30° 30° A P 300 mm B The two wires are connected togetherat A. If the force P causes point…

A: Determine normal strain developed in each wire

Q: 3 m P 3 m B 1.5 mi 3 m E 3 m 1.5 m

Q: Cable AB is supported by a truss structure at A and a pin at B. A uniform distributed load is…

Q: 2.123 A container of weight Wis suspended from ring A. Cable BAC passes through the ring and is…

A: Given: W = 270 lb The tension is the same in both portions of cable BAC. Solution: Free body…

Q: H F 2'm E A C 4 m B D 4 m - 4 m 4 m 4 kN 5 kN F LEI E

A: To find force in member BC

Q: РР РРР A B In the plane truss system, whose loading condition is shown in the figure, there will be…

A: To find the force in member F3 -

Q: The homogeneous 18-kg pulley is attached to the bar ABC with a pin at B. The mass of the bar is…

A: Given: The mass of the pulley is 18 kg. The tension in the cable is 600 N. Consider the figure,

Q: The rigid beam is supported by a pin support at A and steel wires BD and CE (E=200GPA). The steel…

Q: roblem 2 1200N 35° Determine the horizontal and vertical reaction at A, The reaction at G and the…

A: Solution Find the reaction and member force

Q: The two bars AC and CD are homogeneous and weigh 200 N/m. Joints A, C, and Dare ball-and- sockets,…

Q: 10–25. Determine the force in each member of the truss. AE is constant. Show primary and secondary…

A: To Calculate- force in each member of the truss.

Q: Knowing that the rod ABC and the cable BD are both made of steel, determine (a) the deflection at B,…

A: Given :- Rod ABC and cable BD are both made of steel E = 200 GPa To determine :- (a) the deflection…

Q: A IS a Tixed connec Lion. a) determine the normal force the pin at C exerts on the smooth slot. b)…

Q: The gusset plate is subjected to the forces of four members.Determine the force in member B and it's…

A: Given: The value of F is 12 kN. Consider the free body diagram.

Q: Using the method of joints only, determine the force in each member of the truss shown, and state…

Q: 9. Using the Method of Sections, determine the force in member BC, to the nearest 1 Ibs. (Hint: Find…

Q: Determine the force in each member of the truss below. Indicate whether each member is in tension or…

A: A truss is supported by rocker at A and pinned at B. A horizontal 100N force is applied at C. Degree…

Q: Q2 The trus gusset plate is subjected the forces of three members. Determine the tension force in…

Q: F2-7. Determine the horizontal and vertical components of reaction at the pins A, B, and D of the…

A: To find Reaction at D ,moment about A=0 ,VDx9-3x5 cosθx32-3x5 sinθ x2 -8x5-8x7=0VD=14.83…

Q: F2-7. Determine the horizontal and vertical components of reaction at the pins A, B, and D of the…

A: Consider the free body diagram of beam AB. The length the AB is calculated as, The inclination of…

Q: Determine the force P that would produce a tensile force of 25 lb in the cable at E. Neglect the…

A: GIVEN- Tensile Force P=25 F.B.D is given below-

Q: 6 m 5 m 4 m B hc = 2m Ayi D 600 N 450 N

Q: 3 m F X D 6 m- Z 6 m 3 m. F A B 2 m- 2 m 1.5 m

Q: The 6-m pole ABC is acted upon by a 455-N force as shown. The pole is held by a ball-and-socket…

A: Force Vectors:-A=Axi^+Ayj^+Azk^F=455*-3i^-6j^+2k^32+62+22F=-195i^-390j^+130k^ N

Q: Rod AB shown is subjected to the 200-N force. Determine the reactions at the ball-and-socket joint A…

Q: Determine the tension in cable GD, the magnitudes of components of the reaction forces at pin A, and…

A: The given figure is shown below:

Concept explainers

Laws of Equilibrium

A body is said to be in equilibrium if the system of forces acting on the body tends to keep the body at rest, in other words, there is no translation motion or net torque on the body. Under such conditions, the equilibrium conditions are to be applied to analyze the condition. The branch of mechanics that deals with this condition is known as 'statics'. Under equilibrium, there are no net forces on the body.

Question

2, The rigid body ABC is held in place by ball and socket joints at A and C, and cable DE which passes through the right at point B. Find the tension in Cable DE. The coordinates of the points in (mm) are as follow: A, (0,0,600) B, (600,0,600) C, (800,0,0) D, (0,500,300) E, ( 800,500,0) F, (800,0,600)

D
Z
4 Y
ASTI Certified Sourcing
B
F
DE
C
AX
XP = 10KN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. ${3sinh2t+3sin2t}
Please do the conversions. 11404.8 feet to sqft 11404.8 feet to acre
A MarketV X bg Isaac Fra X com/course.html?courseld=172779808OpenVellumHMAC=83742633e6e9579bef30313512e3229e#10001 身口 M Review Part A A paper tube is formed by rolling a cardboard strip in a spiral and then gluing the edges together as shown in (Figure 1). The paper is 1.0 mm thick and the tube has an outer diameter of 100 mm. Determine the shear stress acting along the seam, which is at 50° from the horizontal, when the tube is subjected to an axial compressive force of 200 N. Express your answer to three significant figures and include appropriate units. HA Tz'y = Value Units Submit Request Answer Figure 1 of 1 < Return to Assignment Provide Feedback 40° 200 N 200 N 100 mm P Pearson 11:05 F Copyright © 2022 Pearson Education Inc. All rights reserved. | Terms of Use | Privacy Policy I Permissions | Contact Us | 5/5/20 58°F Mostly cloudy
What is the correct format, in SI units, for stationing 200' from the start of an alignment? 0+200 200+0 O 20+0 2+00
I need the answer as soon as possible
4) Identify thedifferent types ofconstructioncompanies in themarket.And Explain therelationshipbetween differentconstructionorganisations. (with harvard reference) please thank you
Pls Answer briefly. Thank you If you are the designer, how are you going to resolve disputes that may arise between the owner and the contractor.
I really don't get this and I would like to know how you solved it and what the answer is.
Beam Bracket When a steel beam-column structure, such as a high-rise building or a manufacturing plant, is constructed, its columns are erected| before the beams can be elevated, positioned, and welded. The function of a beam bracket is to precisely position a beam and safely transfer the loads from the beam to the columns. The beam bracket consists of a seat plate (the flange) and a web plate. The design considerations include: • Would the maximum stress exceed the allowable stress? • Would the web buckle under the load? The beam bracket is made of structural steel (E = 200 GPa, Poisson's ratio = 0.3, yield strength = 250 MPa). Assume a load of 27KN is uniformly distributed over the seat plate, and that the beam's back face is rigidly welded on a steel column.
Dear Sir/Madam Pls ans quickly Thanks eng
Infrastructure needed to manufacture the stationery line
Provide FBD and detailed solutions. NEED ASAP. Kindly answer correctly