Answered: The beam CBA is supported by a ball and…

The beam CBA is supported by a ball and socket support at A and two cables BD,BE as shown. It is loaded by two forces F=945 KN and P=315 KN.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Solve the following problems using method of joint and section. 1. A Fink roof truss is loaded as…

A: We have to determine the value of force in member DF, FE, and EG as per method of joint and section.…

Q: Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter…

A: Given Esteel=200 Gpa a= 1 m, b= 1.5 m, d= 40 mm, h= 10 mm

Q: Determine the largest load P2 that can be applied to the truss so that the force in any member does…

Q: The three-member truss is used to support vertical load P. If P-200 kN, find the stress of members…

A: Solution -The given values are as follows, If P =200kNCross sectional Area=6000mm3To Determine The…

Q: F2 F1 E 3m 3 m

Q: -1.5 m- 6 kN 2 m 10 kN- C 2 m A B

Q: Solve for the internal reaction for each member of the truss using method of joints

A: Step 1: Step 2: Step 3: Step 4:

Q: If it is known that the center pin A supports one-half of the vertical loading shown. 6 panels at 12…

Q: For the truss shown in the figure: 20KN a) Find the support reactions. b) By inspection, identify…

A: Step 1

Q: Determine the support reactions and member forces of the truss. Assume A to be hinged and D to be…

Q: Determine the internal loadings at point C. There is a pin at A and B is a smooth support.

A: FInd reaction at A:∑ MB=0RA6-1263+33-631.5=0RA=10.5kn

Q: 6-25. Determine the force in each member of the truss in terms of the external loading and state if…

A: To determine the forces in each member of the truss and also state the member is in tension or…

Q: The roof of a single-story storage building shown is subjected to a uniformly distributed load of…

A: Given Data: UDL=2.4kPah=6mL=8m Required- To find the maximum bending moment (kN-m) in beam BE of a…

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. E=200 x 10 N/m2 A-300mm?…

Q: Determine the angle u between the force and the line AO.

A: Consider the free body diagram shown below. The expression for the unit vector of the force is give…

Q: Select member FC and CB in the truss to carry the inclined force P. Set the allowable tensile ress…

Q: 3 m *9-32. Determine the force in each member of the truss. AE is constant. 4 m- B shakes and a pe…

Q: Determine (approximately) the force in each member of the truss. Assume the diagonals cannot support…

A: Draw the free-body diagram of the truss. Calculate the angle θ as follows. tanθ=43θ=53.13∘

Q: The space truss shown below is supported by a ball and socket joints at A, B, E, and F. It is…

Q: The beam CD is rigid and it rests on two posts as shown. Both posts are made of steel and have a…

Q: A kN -2.5 m- D 1.5 kN . 4 m 3 kN F 4 m B 3 kN 4 m A H -4 m- Hy = AY= hine roller

A: given tower truss to find forces in members BG, FG, CF and EF using method of sections.

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5…

Q: F9-5. The beam is subjected to the load at its end Determine the maximum principal stress at point…

A: Given : Determine the maximum principle stress at point B ? Concept - Principle stresses are taken…

Q: Determine the force in member BE of the loaded truss. State if in tension or compression.

A: θ=tan-1(612)=26.565°x6=412x=2mα=tan-1(42)=63.43494

Q: The space truss shown below is supported by a ball and socket joints at A, B, E, and F. It is…

Q: F3-3. Determine the force in each member of the truss and state whether it is in tension or…

A: All data is given belowNeed to find find each member's force.

Q: Determine the force in EA member of the truss, and state if the members are in tension or…

Q: Determine the force in member BE of the loaded truss. 5 kN 45⁰ A B D 1 m 45⁰ 2 kN F 1 m

Q: Compute asial forces in all truss members P2: In the previous problem, determine the force in…

Q: Determine (approximately) the force in each member of the truss. Assume the diagonals can support…

A: Consider the free body diagram of the truss;

Q: T 2 m 3 kN 2 m G LEX -3 m -1.5 m- (b) *Assume A to be hinged and D to be roller. 6 kN F 3 m- -3 m- 3…

A: To Determine :- The support reactions and member forces on the truss.

Q: Determine (approximately) the force in members CE, GE, and GH of the portal frame as shown in figure…

Q: 6-25. Determine the force in each member of the truss in terms of the external loading and state if…

A: Given : P = 2 kN Determine the forces in each member of the truss ?

Q: 1. Compute the force in member FEF 2. Compute the force in member FED

Q: 3 m A -2 m B 5 kN 2 m- E 5 kN -2 m D 5 kN

Q: Determine the absolute maximum moment in the girder due to the loading shown. 10 k 8 k 3k4 k Tim 3…

Q: 4/2 Determine the force in each member of the loaded truss. A 30° 60° k B

A: To find force in all members of the truss

Q: 4. Select member FC and CB in the truss to carry the inclined force P. Set the allowable tensile…

Concept explainers

Plane and Space Trusses

In civil engineering, a truss is the most important structure that forms the most fundamental member of any building structure and commercial complexes. Trusses are composed of individual members or links that are interconnected by suitable joints, such as rivets, welds, or bolts, and nuts. In trusses, the interconnection leads to the formation of a series of triangles joined together such that all the triangular members behave as a single rigid body. In a simple truss, three members are connected to form a truss member. In trusses, the force always acts at the joints or the interconnection between the individual members.

Question

The beam CBA is supported by a ball and socket support at A and two cables BD,BE as shown. It is loaded by two forces F=945 KN and P=315 KN.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Explanation

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q1) Determine the force in member BC of the truss shown, the truss is hinged at A and supported on rollers at D, the roller is on a sloped surface with 45° to the horizon. ( all the forces in kN and dimensions in meter). Di Di B D2 E DI Di FI F2
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E seel = 200 Gpa and a= 1.5 m, b= Im, d=30 mm, h= 8 mm 2a
For the given girders of the frame shown which carries a uniform load of 14.6 kN/m along span GH and HI and a unifoem load of 33.8 kN/m along soan DE and EF Dimensions are given as follows: A=3.7m B=5.9m C=7.5m Using the approximation frames under vertical loads. Compute the value of the absolute moment at reaction B. (kN-m) Answer: 46.7 Need solution
Solve the given truss below if L-5m and F-380 kN L. :- L- L. G 3.6 m H. I J L. F F F F F Calculate the force in member GL kN LE. kN KE, KN KL. KN DE, KN
please solve this with a complete solution. Thank youuuu
(1) The beam AB will fail if the maximum internal moment at D reaches 800 Nm or the normal force in member BC becomes 1500 N. Determine the largest load w it can support. (Supports A & C are pinned and there is an internal hinge at B) 4 m D 4 m W B -4 m- 3 m C
For the truss shown below, applied loads are PB = 73 kN, PC = 36 kN and PD = 15 kN. Using the sign convention 'tension positive', select the correct answer for the axial force in member GH in kN: К F AR G В Рв 4@3m=12m O 1. The axial force in member GH is -60 kN. O2. The axial force in member GH is -78 kN. O 3. The axial force in member GH is -67.1 kN. Н Pc J D Ро K E 4m ?
A)determine determinacy and stability b) identify the zero force members
Q12. Acontinuous beam is built in at A and is carried over rollers at B and C as shown in figure, AB = BC = 12 m. It carries an uniformly distributed load of 3 kN/m over AB and a point load of 24 kN over BC which is 4 m from the support B. Value of E and I are 200 Gpa and 0.2 x 10-3 m2 respectively uniform throughout. Calculate the fixed end moments.
Determine the force in each member of the pin-connected truss. AE is constant. Use force method