Answered: Solve the following problems using…

Solve the following problems using method of joint and section. 1. A Fink roof truss is loaded as shown. Determine the force in member DF, FE, and EG.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: for the given truss, calculate the member force at AB in kips. express your answer in 2 decimal…

Q: Directions: In an A4 size bond paper, analyze an unsymmetrically loaded simple truss. Use the same…

Q: Problem 5: Determine the force in all the members of the comp or compression. Hint: Substitute…

Q: analyze the shown truss using: 1- force method 2-stiffness method assume point C is roller support…

A: Truss Analysis: Force Method vs. Stiffness MethodWe'll analyze the given truss with a roller support…

Q: Refer to the truss shown a. Determine the maximum positive ordinate for member DC. b. Determine…

A: First we will draw the Influence lines for member AB and DC

Q: Problem 5: Method of Sections Inputs: ● ● ● B H I a d = 4 m a = 3 m (all horizontal members are this…

A: Given data in question Load 45 kN Span 3 m each and 4m To find out Force in member CJ

Q: SOLVE FOR EACH FORCE MEMBER OF THE GIVEN TRUSS. (USE METHOD OF JOINTS) E P₁= 30N P₂=15N P₁ A F -3m B…

Q: P=53

Q: Determine the largest force P that can be applied to the truss so that members in tension do not…

A: Given:- Tension do not exceed=5kN compression do not exceed=3.5kN Weight of each member=200N/m L=5m…

Q: Determine which truss do not carry any tension or compression forces. The truss is subjected to a a…

Q: Situation 3: Determine the force in each member of the truss if W = 100 kg. State if the member is…

A: Truss is given as shown in the figure. W= 100 kg

Q: 8 ft 8 ft 8 ft N A 900 lb L M. 8 ft B 1000 lb 1500 lb 8 ft 8 ft K 1000 lb 8 ft 8 ft 8 ft H A.…

Q: Q2- Determine the forces in members GE, GC, BC of the truss shown in the figure. ( use section…

A: Given above truss we have to find force in member BC, GC, GE

Q: Determine the force in each member of the truss in terms of the load P. A a D P B ca

Q: Find the internal force in the truss member DC. DC = KN, Tension 8 kN C 8 kN B L 45° 45° 60% A E L D

A: To find force in member DC

Q: Analyze the howe truss in the figure. Right Wind load 2.95kn and 5.9kn as indicated. a. Find the…

Q: STRENGTH OF MATERIALS PLEASE WRITE THE SOLUTIONS LEGIBLY AND US 4 DECIMAL PLACES. RATE WILL BE…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: 5. M 5 m 7 m 5 m 7 m

Q: F. F2 F, F2 F. H 0.46 m F D 2.62 m C E GI 2.4 m 2.4 m 2.4 m 2.4 m

Q: Given the following, please solve it using the right approach and please show all your work

Q: 6 m 3m- 3 m G 20 kN 15 kN 4, -3 m 3 m- 1. For the Truss shown, determine the forces in members BC…

Q: Q1- For the truss shown in figure, find the force in members DG and FG. (Assume any value for a )…

Q: Q1: a- Identify the zero-force members in the F kN -2 m E 2 m D truss. b- Determine the force in…

A: The FBD of the beam is shown below: Taking equilibrium equations: ∑fy=0-HE-7=0HE=-7…

Q: a. Assuming all the members have the same properties (E=29,000 ksi, A = 4 in?, Fy = 36 ksi) what is…

Q: •6–129. Determine the force in each member of the truss and state if the members are in tension or…

Q: Determine the force in each member of the truss if W = 100 kg. State if the member is in tension or…

Q: Calculate the forces in members AC, AD, and DE for the loaded truss. Restraining link BC is…

Q: The truss is loaded as shown below. a. Determine the support reactions of the truss. b. Determine…

Q: roof truss shown using method of joints. Specify whether the forces in each member are in tension or…

Q: Question 3: Use the method of Sections to determine the bar forces for the members BC, BG, and HG.…

Q: 1. Determine the force in each member of the truss. State if the member under tension or…

A: Solution: “Since you have asked multiple question, we will solve the first question for you. If you…

Q: Figure Ql shows system of truss. The system having two support which is pin at joint A and roller at…

Q: F G H 3 m A E B 40 kN 40 kN -4 at 3 m = 12 m-

Q: solve the stresses in members DF,DG and EG using method of sections

A: Given data Using method of section

Q: T I Prove that the truss shown is statically determinate and solve for the force members at FG, CF,…

A: Find out: Static indeterminacy member forces using method of joints.

Q: Part B As shown, the truss is loaded by the forces P = 195 lb and P = 400 lb and has the dimension a…

A: Method of joints : The method of joints is a method for calculating unknown forces operating on…

Q: 2,400 N 3,200 N A 2 m 2 m 1 m 2 m F Determine the force in member AF of the truss, and state if the…

Q: Determine the spacing of rivets in mm. Determine the maximum flexural stress at 1 m from the support…

A: Given: τ=100 Mpa σb=220 MPa bearing stress for single shear rivet σb=280 MPa bearing stress for…

Q: 1. The cross-sectional area of each member of the truss is 1200 mm?. Calculate the stresses in…

Concept explainers

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).

Question

Solve the following problems using method of joint and section.
1. A Fink roof truss is loaded as shown. Determine the force in member DF, FE, and EG.

1.5 m 1.5 m, 1.5 m 1.5 m, 1.5 m 1.5 m
6 kN
6 kN
6 kN
F
6 kN
6 kN
D
3 kN
3 kN
2.4 m
В
K
A
-1.8 m-1.8 m-1.8 m--1.8 m-1.8 m-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the truss shown below, P = 9.1 kips, a = 7 ft, and b = 6 ft. Determine the force in member 3 (tension is positive). Give the answer to one decimal place.
Analyze the following indeterminate trusses using the Force Method. Assume a constant EA
Every answers in each solutions must be in 7 decimal points.
Given truss shown, P 50 kN. The tensile oallow 140 MPa, and the compressive Oallow = -85 MPa. If the truss is to support a maximum load P (as given). shear, pin at B is in single shear %3D = 140 MPa, pin at A is in double allow Determine the required Area of the members AB, BC and AC if the Oallowable of the members is 135 MPa. - 450 mm→ B (3) 600 mm (1) 1200 mm
how do i solve the attached civil engineering problem
From the given trusses below, determine the force in the member DE. (kN) Hint: V = -20.9 kN Note: Use two (2) decimal places in the final answer. G H R P M 1.5 m L к 75 kN 75 kN 9 equal bays at 3.0 m each 3.0 m
DIRECTION: Solve and Analyze the following problems in neat and orderly manner. Use your indicated Format. All problem solutions must include FBDS. 10. Determine the force in members BC, HC, and HG. After the truss is sectioned use a single equation of equilibrium for the calculation of each force. State if these members are in tension or compression. 5 kN 4 kN 4 kN 3 kN 2 kN D 3 m 2'm - 5 m -5 m- -5 m--5 m-
please answer with complete solution . structural analysis
For the truss shown: (a) Identify all zero force members (b) Determine the force in members AE and CB and indicate whether the members are in tension or compression. Note that both supports A and B are pins. MUST DRAW A FREE-BODY DIAGRAM. 2 kN- 15 m 4 kN- 1.5 m E с 4m YOB
5)Determine the forces in all members of the truss. There is a pin at A and a roller at D. In answers for truss forces remember you must always indicate if a member is in tension (T) or compression (C); for example, if there was a member JK carrying a 2 kip compressive load the answer would be FJ = 10 K (C) 3 m G 10 kN 6kN E -2.5 m- -1.5 m-1.5 m- -2.5 m
h.w 2 2. Determine the force in each member of the truss. State if the members are in tension or compression. 450 lb
The truss shown is designed to support a staircase. For all questions, indicate whether the members are in tension or compression. Assume that all joints are pinned. Use the method of sections for each part.a. Determine the force in members EG, FG, and HFb. Determine the force in members EF and DF