Q3: A very large thin plate is centered in a gap of widthCo.o6 m) with different oils of unknown viscesities above4 below , one viscasity is tuwice the other. When thep late is pulled at a velocity of Co.3 mls.), the resultingforceone square meter of the plate due fo the viscousshear on both sides is (29 N). Caleulate the viscositiesonof the oils.

Answered: Image /qna-images/answer/528e539e-9151-405b-b976-08640ac268e5.jpg

Q3: A very large thin plate is centered in a gap of width Co.o6m) with d;fferent oils of unknown viscosities above is twice the aother. When the 4 below , one viscosity p late is pulled at a velocity of (o.3 mls.), the resulting one square meter of the plate due to the viscous shear on both sides is (29 N). Caleulate the viscositiss of the oils.

Q3: A very large thin plate is centered in a gap of width Co.o6m) with d;fferent oils of unknown viscosities above is twice the aother. When the 4 below , one viscosity p late is pulled at a velocity of (o.3 mls.), the resulting one square meter of the plate due to the viscous shear on both sides is (29 N). Caleulate the viscositiss of the oils.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What is the most probable cause of this casing failure? 0253 The pipe was under tension, decreasing the burst resistance. The pipe was under tension, decreasing collapse resistance. The axial stress in the pipe have exceeded the yield stress. The pipe failed due to excessive pressure from the interior.
A very lange thin plate is centered in a gap of width Co.06m) with different oils of unknown viscosities above & below viscosity is twice the other. When the one p late is pulled at a velocity of Co-3 mls.), The resulting force meter of the plate due fo the viscous shear on both sides is (29. Calculate the viscosities square on one of the oils.
Soil mechanics ضهقحشكوظز
explain by parts ; the formula and the directions of slopes
Material mechanics,Solve fast
1 Question 14 of 15 -15 Compute the combined moment of the two 70-lb forces about (a) point O and (b) point A. The moment is positive if counterclockwise, negative if clockwise. Assume a = 8.3 in., b = 3.9 in., F = 70 lb. y I F Answers: 10:5 29°C Mostly cloudy Type here to search 04/06 D 1080 1 O EI % 3' & * 8 !!! ENG
The extruded plastic shape has dimensions of D = 35 mm, d = 33 mm, a = 98 mm, and t = 4 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 340 N. (b) If the allowable shear stress for the plastic material is 1400 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? a Answer: (a) TA = КРа (b) V = N
Consider a pressure vessel that is made of two half-spherical domes with 1 ft in diameter, and the cylinder portion is 3 ft in length and is subjected to 100 psi pressure. The maximum tensile strength of the material is 55 ksi. The factor of safety for this design is 1.5. Problem: Determine the minimum thickness for this design.
A cylindrical pressure vessel is fabricated from steel plates which have a thickness of 20 mm. Thediameter of a pressure vessel is 500 mm and its length is 3.0 m. Determine the maximuminternal pressure which can be applied if the stress in the steel is limited to 140 MPa. If the theinternal pressure were increased until the vessel burst, sketch the type of fracture which wouldoccur. Write in a paper with complete solution
Question 8 of 10 View Policies Current Attempt in Progress HO D d The extruded plastic shape has dimensions of D = 37 mm, d = 35 mm, a = 99 mm, and t = 7 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 365 N. (b) If the allowable shear stress for the plastic material is 800 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? N Answer: dik a - / 10 E ||| :
The extruded plastic shape has dimensions of D = 21 mm, d = 15 mm, a = 80 mm, and t = 4 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 320 N. (b) If the allowable shear stress for the plastic material is 1850 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? -D IG N A dik