Current Attempt in Progress The extruded plastic shape has dimensions of D-40 mm, d-34 mm, a-81 mm, and t-8 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V-360 N. (b) If the allowable shear stress for the plastic material is 1100 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? a Answer: (a) TA- (b) V- kPa N

Current Attempt in Progress The extruded plastic shape has dimensions of D-40 mm, d-34 mm, a-81 mm, and t-8 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V-360 N. (b) If the allowable shear stress for the plastic material is 1100 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? a Answer: (a) TA- (b) V- kPa N

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter11: Fracture And Fatigue

Section: Chapter Questions

Problem 6ETSQ

See similar textbooks

Similar questions

Question 8 of 10 View Policies Current Attempt in Progress HO D d The extruded plastic shape has dimensions of D = 37 mm, d = 35 mm, a = 99 mm, and t = 7 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 365 N. (b) If the allowable shear stress for the plastic material is 800 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? N Answer: dik a - / 10 E ||| :
The extruded plastic shape has dimensions of D- 31 mm, d - 25 mm, a - 93 mm, and t - 6 mm.(a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V -(b) If the allowable shear stress for the plastic material is 1550 kPa, what is the magnitude of the maximum shear force V that can beapplied to the extrusion?
show all work step by step A cube of a material with a yield strength of 100x10° N/m is subjectedtothe loads shown on the right. Will plastic/permanent deformation occur as a result of this loading? Consider Both the Tresca (Maximum Shear Stress) and Von-Mises (Distortion Energy) criteria |F,| = 45x10'N →F = 30x10'N →|F, = 60x10°N Cube with side length = 3x10°m Would this change if the directions of F, and F were reversed? Numerical Values Required.
An applied torque results in a shear strain (y) of 3.75 x 103 in a solid circular steel shaft. At this strain, a portion of the shaft cross- section yields as shown in Figure 2. Determine the magnitude of the applied torque. Take G = 80 GPa and yy = 2.8125 x %3D 10-3 FIGURE 2: Plastic zone 50 mm 200 mm Elastic core
A punch of 20 mm diameter is used to punch a hole in 8 mm thick plate. If the force required to create a hole is 110 kN, the average shear stress in the plate will be nearly 1.410 MPa 2.320 MPa 3. 220 MPa 4. 140 MPa
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 42 mm. The diameter of the pressure vessel is 450 mm and its length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa, and the circumferential stress is limited to 60 MPa. *
The polymer bar shown in the figure below has a width of b = 59 mm, a depth of d = 90 mm, and a height of h = 258 mm. At a compressive load of P = 120 kN, the bar height contracts by Ah = -2.40 mm, and the bar depth elongates by Ad = 0.37 mm. At this load, the stress in the polymer bar is less than its proportional limit. Determine: (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar width b. P Rigid plate (a) E = i (b) v = (c) Δb = i i GPa mm b h Rigid base
The polymer bar shown in the figure below has a width of b=55b=55 mmmm, a depth of d=104d=104 mmmm, and a height of h=274h=274 mmmm. At a compressive load of P=120P=120 kNkN, the bar height contracts by Δh=−2.60Δ⁢h=-2.60 mmmm, and the bar depth elongates by Δd=0.36Δ⁢d=0.36 mmmm. At this load, the stress in the polymer bar is less than its proportional limit. Determine: (a) the modulus of elasticity. (b) Poisson’s ratio. (c) the change in the bar width bb.
Q) If the failure of shearing stress in a steel plate is 2,300KN, determine (a) the force required to punch a 32 mm diameter hole in a 10mm thick plate and, (b) the corresponding normal stress ina punch. Explain it correctly
The polymer bar shown in the figure below has a width of b = 59 mm, a depth of d = 96 mm, and a height of h = 286 mm. At a compressive load of P = 150 kN, the bar height contracts by Ah = -2.40 mm, and the bar depth elongates by Ad = 0.37 mm. At this load, the stress in the polymer bar is less than its proportional limit. Determine: (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar width b. P Rigid plate (a) E = (b) V = (c) Ab = i i GPa mm k b h Rigid base
The polymer bar shown in the figure below has a width of b = 42 mm, a depth of d = 97 mm, and a height of h = 253 mm. At a compressive load of P = 125 kN, the bar height contracts by Ah = -2.40 mm, and the bar depth elongates by Ad = 0.40 mm. At this load, the stress in the polymer bar is less than its proportional limit. Determine: (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar width b. Rigid plate h Rigid base (a) E = i (b) v = i (c) Ab = i GPa mm b
A punch of 20 mm diameter is used to punch a hole in 8 mm thick plate. If the force required to create a hole is 110 kN, the average shear stress in the plate will be nearly (a) 410 MPa (b) 320 MPa (c) 220 MPa (d) 140 MPa 95