determine the yield angle of twist (in radians) in the rod О 183.24 х 10-3О 282.47 х 10-3О 271.39 х 10-3О 194.85 х 10-3 A solid steel rod is 1.5 meters long and has a diameter of 20 mm. The steel rod is assume tobe an elastoplastic material with G = 77 GPa and a yield shear stress of 145 MPa.%3D

Answered: Image /qna-images/answer/c589a984-f9d7-42db-9905-22d1f86a0c96.jpg

Answered: determine the yield angle of twist (in…

Engineering

Civil Engineering

determine the yield angle of twist (in radians) in the rod

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

please use ijk components while doing calculations
8) If the elongation of wire BC is 0.2 mm after the force P is applied, determine the magnitude of force P. The wire BC is A36 steel and has a diameter of 3 mm. 200 G Pa E A36 400 mm 300 mm B 200 mm-
bending moment changes sign shear force is maximum iii. bending moment is maximum GROUP-B 1) Derive the relationship between Young's modulus (E) and Bulk Modulus (K). 2) For the aluminium shaft shown (G = 27 GPa) below, (a) determine the torque T that causes an angle of twist of 4°, (b) the angle of twist caused by the same torque T in a solid cylindrical shaft of the same length and cross-sectional area. 1.25 m 18 mm 12 mm
600 -400- 600 800 G| P2 P3 E F Tha at y pnywty i A - 100 mm E - 200 GPa A- 150 mm E- 200 GPa A130 mm E- 70 GPa 700 A- 50 mm E- 83 GPa P1 d. 30° o B 500 All dimensions are in millimeters.
Problem I A 2.25-kg slender rod AB and a 1.85-kg slender rod BC are connected by a pin at B and by the cord AC. The assembly designed by engineers can rotate in a vertical plane under the combined effect of gravity and a couple M applied to rod BC. Knowing that in the position shown, the 300 mm angular velocity of the assembly is zero and the tension in cord AC is equal to 25.0 N, determine; A (a) the angular acceleration of the assembly (b) the magnitude of the couple, M 400 mm C 400 mm AM B
HW. 9-3. The state of stress at a point in a member is shown on the element. Determine the stress components acting on the inclined plane AB. Solve the problem using the method of equilibrium described in Sec. 9.1. 60 400 psi *650 pகம்
5. A 12-mm-diameter steel [E = 200 GPa] rod (2) is connected to a 30-mm-wide by 8-mm-thick rectangular aluminum [E = 70 GPa] bar (1), as shown in Figure. Determine the force P required to stretch the assembly 10.0 mm. (1) 0.45 m B 1.30 m
Statics Civil engineering The plate is suspended how using three cables applying the forces shown. Express each force as a cartesian vector. Use 3 digits after the comma.
In the figure, the ac element is rigid and is held with the bars AB, CD and EF, each of which has a cross-section of 145 mm ^ 2, without a blank and without tension. The AB bar can be changed with a screw mechanism over 0.75. The step of the screw in a full turn is 1.5 mm. If the screw is rotated 1.5 steps in the direction of shortening the length of the EF rod, what is the value of the force that will occur on the EF rod? Take the elastise modulus 210 GPa for all bars
civil engineering. need help.
Calculate the maximum intensity w of the uniform distributed load that can be applied on the beam without causing the compressive members of the supporting truss to buckle. The members of the truss are made from A-36-steel rods having a 60-mm diameter. Use FS. = 2 against buckling. Need accurate answer only
5- Replace the forces acting on the plate by a wrench. Specify the force and couple moment for the wrench and the point P(x, y) where its line of action intersects the plate. F, = |-300k) N %3D Fe= [200j| N 2m 500N 30 F = (4001) N