Q3 A thin rod of 3 cm length having a thermal diffusivity coefficient (a) of 0.835 cm²/s is initially kept at a temperature of 0 °C. The rod is insulated at all points except at its ends which are kept at all times at T(0) -5 °C and T(3) = 10 °C. Use the explicit method to solve for the temperature distribution in the rod at t= 0.2 second using the following information; Ax=1 cm, At = 0.1 second, and λ = a At/Ax².

Q3 A thin rod of 3 cm length having a thermal diffusivity coefficient (a) of 0.835 cm²/s is initially kept at a temperature of 0 °C. The rod is insulated at all points except at its ends which are kept at all times at T(0) -5 °C and T(3) = 10 °C. Use the explicit method to solve for the temperature distribution in the rod at t= 0.2 second using the following information; Ax=1 cm, At = 0.1 second, and λ = a At/Ax².

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Solve fast and solve correctly. I will rate.
10. From Newton's law of cooling, the boiled egg submersed in water in the diagram below will cool according to dI = -0. 1(T – a), T(0) = 100°C . Solve this differential equation and express T in terms of a. Do not use the integrating factor method. Present your solution with T as the subject. Use your solution to solve the following: If after 1 = 10 time units this egg cools to T = 2ª°C , what was the value of a (a is the temperature of the water in the glass which is assumed to have remained constant)?
any help would be much appreciated thanks
I need the answer as soon as possible
A wood fire with a temperature of 1110F is at the other side of a 10 square ft wall that has a 6-inch layer of firebrick, 3-inch layer of concrete, and 6 inches of regular bricks. The thermal conductivity in Btu of each material is as follows: 0.27, 0.76, and 0.98 respectively hr-ft-° Solve for the heat conducted through this wall and the temperatures measured between the layers if the temperature at the other end of the wall is 150F?
Please solve it complete in 30 minute
A J- type thermocouple is used to measure the temperature in a heating process. Sheath material used is SS316. The length of the sheath is 10mm and thickness is 0.2mm. Find the time constant of the sheath. Material Q(kg/m3) s(J/Kg - oc) K(W/m-k) Platinum 21450 130 71.6 SS304 8030 500 21.4 SS316 7990 500 21.4 SS410 7750 460 24.9 Air 1.20 1005 0.025 MgO Powder 3580 877 26.8 Silicon compound 3210 800 3 Time constant of the bare material is, T= Answer
2. The slab shown is embedded in insulating materials on five sides, while the front face experiences convection off its face. Heat is generated inside the material by an exothermic reaction equal to 1.0 kW/m'. The thermal conductivity of the slab is 0.2 W/mk. a. Simplify the heat conduction equation and integrate the resulting ID steady form of to find the temperature distribution of the slab, T(x). b. Present the temperature of the front and back faces of the slab. n-20- 10 cm IT- 25°C) 100 cm 100 cm
One-dimensional, steady-state conduction with uniform internal energy generation occurs in a plane wall which is subject to convection on the left side at x = 0 and being well-insulated on the other.a) Specify the mathematical model defining T(x): provide a governing differential equation and appropriate boundary conditions. Express your answer in terms of defined variables rather than numerical values with units. b) Solve for the temperature profile T(x) referencing the x-origin as shown on the left surface (again expressing your answer in terms of defined variables rather than numericalvalues.) c) Find the maximum temperature in the wall and the wall surface temperature if the volumetric generation is qdot = 1 MW/m^3 with the remaining parameters as specified in the figure.
!
1