H +x L→∞0 B The temperature at the base is 498 K, and the temperature of the surrounding fluid is 273 K. The heat transfer coefficient between the surface of the fin and the surrounding fluid is 22 W/m²K, and the thermal conductivity of the fin is 252 W/mK. The dimensions of the fin are: H = B = 10 mm, L = 20 cm. a) The total heat transfer through the single fin is b) The effectiveness of the fin is c) The efficiency of the fin is _w.l

H +x L→∞0 B The temperature at the base is 498 K, and the temperature of the surrounding fluid is 273 K. The heat transfer coefficient between the surface of the fin and the surrounding fluid is 22 W/m²K, and the thermal conductivity of the fin is 252 W/mK. The dimensions of the fin are: H = B = 10 mm, L = 20 cm. a) The total heat transfer through the single fin is b) The effectiveness of the fin is c) The efficiency of the fin is _w.l

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(a) Write equations for the internal forces at J (axial (F), shear (V), and bending (M)) in terms of only P and a. (b) Graph your equations as functions of P, using a = 45°, from 0 < P < 1000 N. Use your graph to answer the following conceptual questions: 1. Which quantity (F, V, or M) is most affected by changes in P? 2. Based on your diagrams and graphical results, for positive values of P... I. Is point J under tension or compression? II. If the structure fails (snaps) at a point just to the right of J, which direction does your diagram indicate point J will travel (up or down)? III. Which direction do your results indicate member BC will tend to bend, concave up or down? 3. For different values of a, what will happen to these lines? Choose all that apply: a. They will shift up/down b. They will shift left/right c. They will rotate (change slope) d. Nothing (c) Graph your equations as functions of a, using P = 100 N, from 0 < a < 2π. Use your graph to identify what value of a…
A solid rectangular parallelepiped is made of aluminum and is initially at 20 C. The base is a 2 cm by 3 cm rectangle and the height of the parallelepiped is 5 cm. The parallelepiped is now dropped into hot oil at 150 C. Find: a) the temperature of point P and b) the temperature of the center of the parallelepiped after 2 min of exposure to hot oil. Point P is located 1 cm above the center plane and1 cm from each side.
calculations. A common room at a facility is used by personnel for food consumption and resting (Fig. 2). An air conditioning system is required for providing comfortable temperature of 23°C. You are asked to select the room dimensions (X= 10m, Y=2.4m and Z= 15m) and design a split air conditioning system suitable to meet the requirements for climatic conditions of a humid subtropical climate with long-term annual average high temperature of 26.4°C and minimum low of 16°C. The room can accommodate up to 6 - 12 staff members. The following kitchen appliances are used in the room: coffee machine, 2 microwaves, cooktop and dishwasher. S E COFFEE 128 O FFEE FIGURE 2. Common room layout Z X COFFEE Y
What are the problems in statically intermediate equations?
Looking for a handwritten solution as fast as possible.
a. State carefully the differences between wire frame and solid modeling? b. Verify the Euler's equation for the following three-dimensional solid model? 20 10 25 10 30 20 RI 07
Hello. Can you please help answer the question shown in the photo? It is a 3-part question which I have attempted many times. I was able to calculate the correct answer for part 2, but part 1 and part 3 still says I am incorrect. Please show how to properly solve the problem. The topic is heat transfer. Thank you.
Show all working explaining detailly each step Answer must be typewritten with a computer keyboard! Answer Q7
The director of the swimming club runs an experiment by examining the impact of 11 factors on average race times across 6 swimming tournaments (6 experimental runs). (Choose all that are true) The full model should be fit as the higher order interactions are likely to matter and there are sufficient degrees of freedom for it. The design is a supersaturated design because the number of factors is greater than the number of runs - 1. Backwards selection should be used to determine which factors significantly impact race times as model refinement will be needed. Forwards selection should be used to determine which factors significantly impact race times as model refinement will be needed and there are insufficient degrees of freedom to fit the full model.