Q2/The following are available reservoir data: Pay zone thickness (50) ft., the original permeability of the Indiana zone (128) md and radius of drainage area equal to (720) ft., average reservoir pressure (2750) psi and the pressure drop equal to (1000) psi , oil formation volume factor (1.3) BBL/STB, as a result of stimulation operation formation permeability improved to (145) md with affected radius (0.4) ft, well bore radius (0.375) ft, and 50% of the formation perforated at the center by bullet guns with 2 shots/ft, bullet penetrate with one side penetration, and oil viscosity (0.5) cp. Determine all of the following: 1. Ideal flow rate. 2. Actual flow rate. 3. Pressure drop due to skin and flow efficiency.

Q2/The following are available reservoir data: Pay zone thickness (50) ft., the original permeability of the Indiana zone (128) md and radius of drainage area equal to (720) ft., average reservoir pressure (2750) psi and the pressure drop equal to (1000) psi , oil formation volume factor (1.3) BBL/STB, as a result of stimulation operation formation permeability improved to (145) md with affected radius (0.4) ft, well bore radius (0.375) ft, and 50% of the formation perforated at the center by bullet guns with 2 shots/ft, bullet penetrate with one side penetration, and oil viscosity (0.5) cp. Determine all of the following: 1. Ideal flow rate. 2. Actual flow rate. 3. Pressure drop due to skin and flow efficiency.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The hydraulic conductivity (K) of a homogeneous sandy clay mix aquifer is 2x10-3 cm/sec. The hydraulic gradient (groundwater surface slope) of the phreatic (water table) aquifer is 0.01 and the aquifer's effective porosity is 0.35. Calculate the average (advective) velocity of a conservative contaminant discharged to this groundwater unit. Enter your answer rounded to the nearest tenth in meters/year. Example: 5.2 , 65.7, 224.3 would all be proper forms of your answer.
Question: A rectangular primary sedimentation basin is to be designed for an activated sludge treatment plant serving a municipality. The regulatory agency criteria for primary sedimentation basins used for activated sludge system are as follows: peak overflow rate (S) = 80 m3/d-m2, average overflow rate (S) = 40 m3/d-m2, peak solids loading = 50 kg/d-m2, peak weir loading = 372 m3/m-d. The average flow to the basin is 12 000 m3/d. Calculate the tank surface area in m2. Calculate the peak flow rate in m3/d. Calculate the total suspended solids concentration in the incoming flow to the basin (mg/L) Calculate the total weir length (m)
Answers: a) 360 cm3/sec b) 1.12 c) 2.8 meters
i need the answer quickly
Estimate the Q that produced a drawdown in a 1 ft diameter well of 5 feet above the bottom of a pressurized aquifer with a 35 ft thickness and a head in a monitoring well 55 ft away 25 ft above the bottom of the aquifer in a clean course sand aquifer with K ~ 3*10^(-3) ft/sec.
a) Choose with reason, one (1) reserve estimation method that allows reservoir production forecasting using empirical equation, and one (1) reserve estimation method in prediction of oil original in place (OOIP) using static pressure data.
for the following conditions, determine the groundwater infiltration. new two lane highway, lane width 12ft; shoulder width 10ft; length of crack 20ft; rate of infiltration 0.5ft^3/day/ft^2; spacing of crack 25ft kp=15*10^-5 ft/day
What change in velocity would be necessary if the bed was to extend by 18%?(Giving Date: Sand media size: 3 mm, operating bed depth of 0.5 m and Minimum fluidization Velocity for sand filter used in wastewater treatmen= 4 m/s, density of sand media: 2000 kg/m3 and its porosity = 0.3)
The figure is a plan view of a confined aquifer showing two contaminated zones, 1 and 2. The aquifer has a saturated thickness of 80 ft, hydraulic conductivity of 42 ft/d, and the regional hydraulic gradient is 0.0075 from right to left as shown. A pumping well with a flow rate of 170 gpm is planned to run continuously at the location shown, and form a stable (equilibrium) capture zone. You may assume that the 2500 ft distance from the well to zone 1 is long enough that the capture zone has reached its maximum width. 2 200 ft Determine: pumping well 2500 ft 700 ft regional flow direction 1. If contamination from zone 1 find its way to the pumping well? Provide support for your answer with a capture zone analysis or contaminant simulation model. 2. If contamination from zone 2 find its way to the pumping well? Provide support for your answer with a capture zone analysis or contaminant simulation model.