Q2/A/ Air enters the compressor of a gas turbine at 100 kpa and 25°C. For a pressure ratio of 5 and a maximum temperature of 850°C, determine the work ratio (WR) and the thermal efficiency for this Brayton cycle. Assume constant specific heat.

Q2/A/ Air enters the compressor of a gas turbine at 100 kpa and 25°C. For a pressure ratio of 5 and a maximum temperature of 850°C, determine the work ratio (WR) and the thermal efficiency for this Brayton cycle. Assume constant specific heat.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

show complete and clear procedure
Q1: A spring-loaded piston-cylinder device contains 1 kg of carbon dioxide. This system is heated from 100 kPa and 25 °C to 1000 kPa and 300 °C. Determine the total heat transfer to and work produced by this system if: V1=0.563 m3, V2= 0.108 m3, and AU= 180.7 kJ. Answer: 250.1 kJ, 69.4 kJ
3 moles of an ideal diatomic gas undergoes the three process cycle as depicted in the figure below. The cycle is composed of an isobaric, isovolumetric, and isothermal process. P. V, V. For the given parameters pa=Pp = 1.3-10° Pa and V.=0.7 m³, V, = V= 0.35 m³ calculate the following. (Take the universal gas constant as R= 8.314 J mol1.K-1) a) The pressure P c Pa b) The net work done by the gas W, net c) The heat entering the cycle QH= d) The thermal efficiency of the cycle (in percent): e = %
Air flows steadily between two sections in a duct. At section (1), the temperature and pressure are T₁ = 87°C, and p₁ = 305kPa (abs), and at section (2), the temperature and pressure are T₂ = 182°C, P2 = 175 kPa (abs). Calculate the (a) change in internal energy between sections (1) and (2), (b) change in enthalpy between sections (1) and (2), (c) change in density between sections (1) and (2), (d) change in entropy between sections (1) and (2). (a) U2-U1= i (b) h₂-h₁ = (c) P2-P1= (d) $2-$1= J/kg J/kg kg/m³ J/(kg*K)
Benzoic acid, C;HsO:H, is typically used as a çalibrant for determining the specific heat of bomb calorimeters. It combusts via the following unbalanced chemical reaction: C,H5O2H (s) + 02(g) → CO2 (g) + H2O(1) 3. For this experimental setup and reaction, the constant volume heat flow is known to be gy = -26.979 kJ. Over the course of the reaction, the temperature rose from 19.863 °C to 22.540 °C. Calculate the heat capacity, Cou, for this calorimeter in kJ °C-!.
A piston/cylinder setup contains 1 kg of air at 20°C with an initial volume of V1=0.1 m3, as shown in Fig. Q7. Initially, the piston rests on some stops, but it is possible for it to move within the cylinder without friction. To lift the piston and start such motion, an air pressure of 1400 kPa is required. Now, heat is transferred to the system so that the temperature of the air reaches to a final value of 300°C. Fig. Q7 A. Which statement is true? The air can lift the piston before the temperature reaches to 300°C The air cannot lift the piston before the temperature reaches to 300°C
Air contained in a piston-cylinder system undergoes a polytropic process. Pv1.3 = constant P1 = 100 kPa pressure and T1 = 220C temperature to P2 = 500 kPa pressure is compressed. Calculate the work and heat exchanges per unit mass during the process and find their directions. Determine.
I need the answer as soon as possible
0.1 kg of nitrogen gas at 200 kPa and 50°C is contained in a piston-cylinder arrangement. The piston is moved compressing nitrogen until the pressure becomes 1 MPa and temperature becomes 150°C. The work done during the process is 40 kJ. Calculate the heat transferred from the nitrogen to the surroundings. C y for nitrogen = 0.75 kJ/kg K.