Q21. i) ii) Two watt-meter method is being used to measure power in a 3-phase 3-wire star-connected system with inductive load having 260V line voltage and 25 A phase current & phase angle of 45°. Calculate the total power consumed by the load. Estimate the reading on each wattmeter.

Q21. i) ii) Two watt-meter method is being used to measure power in a 3-phase 3-wire star-connected system with inductive load having 260V line voltage and 25 A phase current & phase angle of 45°. Calculate the total power consumed by the load. Estimate the reading on each wattmeter.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: A 4.4 kVA power and 220 V 1-phase load is fed from a distribution line with a total resistance of…

A: Given, Zl=0.2+j0.3Load Voltage = 220 VLoad Power = 4.4 KVAPower factor =1

Q: In the experiment No.1, the power measurement using two wattmeter method for delta connected load,…

A: The solution is given below the statement is false.

Q: For an ac three-phase four wire system, having a voltage of 415 V, with load of 120 kW and…

A: Given three phase four wire systemHaving voltage V=415 vLoad P=120 kw Resistance R=0.05 ΩPower…

Q: Q4) Two wattmeters are connected to measure the input power of a balance three phase circuit. The…

A: In this question we need to find a power factor for the given reading of wattmeter.

Q: If the current and voltage are 90 degrees out of phase, the power factor will be? a) 0 b) Infinity…

Q: if a wattmeter was connected to a 240 volt single phase circuit that contained only capacitors and…

A: Given A wattmeter Supply voltage V=240 v Circuit load :Capacitors only (Purely leading power…

Q: Question 3. The two parallel loads in the figure shown below are as follows. Load 1 absorbs 24 kW…

Q: How will you calculate the average wattmeter reading in one wattmeter method for balanced load?

A: This is the schematic diagram for the measurement of power using the one-wattmeter method. The…

Q: 1. Discuss the features of two-wattmeter method of power measurement. 2. What is the significance of…

Q: A Y connected alternator was tested for its effective resistance. The ratio of the effective…

A: I have written this solution as handwritten solution. Hope you find the solution clear.

Q: The power flowing in a 3-0, 3 wire balanced load system is measured by the two wattmeter method. The…

A: Given values are - WA=W1=500WWB=W2=-100W Given that power flowing in 3 phase 3 wire balanced load…

Q: Two power system areas operating at a nominal frequency of 60 Hz are connected with a tie line, and…

A: Step-1->

Q: For a 3 phase 975 KVA generator.... if the voltage rating is 2400V what is the current rating at…

A: The power factor is calculated as follows, From figure the general formula for power factor is,…

Q: Three single phase loads are connected to the 400 V, three phase lines, 60 Hz. Load 1 operating at 3…

Q: Three similar coils, each of resistance 10 Q and reactance 10 Q, are connected in star across a…

Q: Between line a and b , line b and c and line c and a of a balance 230V 3-phase systen are connected…

A: It is given that: 10 A @ unity p.f.20 A @ 0.5 p.f. lag30 A @ 0.866 p.f. lag

Q: Combine the characteristics of the alternators and calculate the current deliveredand Power…

A: To calculate the current and power delivered by each alternator when connected in parallel, we need…

Q: At what power factor will one of the wattmeter reading be zero in a three-phase system???

A: W1=VLIL cos(30-∅)W2=VLIL cos(30+∅)

Q: When the two-wattmeter method is used to measure the input power of a balanced load, the readings on…

A: Given,

Q: From the experiment 2, the two wattmeter method is used to measure the power. In that pressure coil…

A: The detailed answer is solved below according to the given parameters and instructions in the…

Q: Consider a simple positive phase sequence, three-phase, three-wire system operated at 50 Hz and with…

A: In this question, we need to determine the power supplied by the three-phase source. Three phase…

Q: In a 3-phase balanced star connected system, the least number of wattmeter essential to measure the…

A: in balanced system , total power = 3* power in single phase so total power in balanced three phase…

Q: Refer to Figure 8-31 to answer the following questions. Assume that a line voltage of 12,470volts…

A: Analyze the given circuit, we will observe that: The primary winding of the Transformer is Delta…

Q: . Calculate the voltage regulation of a 230V, three phase alternator supplying the following loads…

A: As per our policy i have attempted first three sub-parts Given data: Voltage regulation is: 230 V

Q: 31. A 3-phase 3-wire star-connected load consists of a capaci tive reactance of 100 £2 in the red…

A: It is given that: XC=100 ΩR=100 ΩVl=440 V

Q: * Two generators, rated at 100 MW and 400 MW, are supplying power to a network. The system frequency…

A: we need to tell the value of droop R of the 100MW generator.

Q: Prove that two-wattmeter method can be used to measure three-phase power in a star-connected load.

A: This is an easy problem. Look below for solution..

Q: In 3-phase two wattrneter power measurement for delta connected load, the neutral is needed to…

A: In two watt meter of measurement of power we current coils of two wattmeters are series with two…

Q: For the figure shown below, calculate (a) the currents I1, I2 and I0 and (b) find the average power…

A: Asked to calculate,(a) the currents I1,I2 and Io(b) Average power delivered to the load.

Q: Three single phase loads are connected to the 400 V, three phase lines, 60 Hz. Load 1 operating at 3…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Please calculate the impedance in a phase. b) Please calculate the line currents. c)Please draw the…

A: In this question, we need to determine the impedance per phase, line currents and draw the phasor…

Q: A 5 kVA, 208 V, three-phase AC is connected in wye. Determine: the voltage of each coil of the phase…

A: In this question we need to find voltage of each coil of the phase windings and the coil current at…

Q: Two wattmeter are used for measurement of power in load test of three phase induction motor rating 5…

A: Three phase induction motor is star connected. Motor ratings are, Power, P=5 kW line voltage VL=415…

Q: nd current of a three – phase load are as follows: Voltage: 3.6 kV, 8 degrees Current: 37 A, 45…

A: We are given voltage and current of a three-phase load as follows:V=3.6 kV, 8 degrees,Current = 37…

Q: A 3-phase, 30 MVA, 10 kV alternator has internal reactance of 5 % and negligible resistance. Find…

Q: 1. If two wattmeters are used to measure total power in a three-phase three-wire system does each…

A: NOTE- As per the rules we can answer only 3 sub-parts, please post the remaining sub-parts as the…

Q: In two wattmeter method of 3-phase power measurement, the readings of reading of any one of the…

A: The power factor in two wattmeter method is given by the formula :

Concept explainers

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.

Question

Q21.
i)
ii)
Two watt-meter method is being used to measure power in a 3-phase
3-wire star-connected system with inductive load having 260V line
voltage and 25 A phase current & phase angle of 45°.
Calculate the total power consumed by the load.
Estimate the reading on each wattmeter.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

26. In a two wattmeter method of power measurement of a balanced load, wattmeter readings are -66.8 kW and -16.8 kW. The reversing switch is operated in the first wattmeter showing -66.8 kW. find (a) total input power and (b) load power factor.
In the balanced three phase power measurement using two wattmeter method, each wattmeter reads 18 kW , when the pf is unity. What does each wattmeter reads when the pf falls to (i) 0.707 lag and (ii) 0.422 lag. The total three-phase power remains unchanged. (i) W1 at 0.707 lag (i) W2 at 0.707 lag (ii) W1 at 0.422 lag (ii) W2 at 0.422 lag
In tan" tan M- M+ M OCT Evaluate (130 points); Use 3 decimal places. 1. The annual load of a substation is given in the following table. During each month, the power is assumed constant at an average value. Find the (a) average load and (b) the annual load factor. Annual System Load January 8 February 8 March 4 April 2 May 6 2, T- June 12 sing July 14 pha: August 14 idea September 10 imp October 8 5Y5 November 6 mac December 8 00 deliv
QiA 3 Phase 10 MVA KV y connected alternator is protected by merz- price civentating current system, the star Point is earthed therong a resistance of 52. If CTS have afatio of 1000/5 and the relay is set to operate when ther is overload with 30% (xen+ ) ) Cateolate M 1905 Xav 40x0.5 1) the percentage of each phase of stator Winding which is protected. If the reactance of 1000000" the stator winding is tot. Per Phase. 2) The minimum value of carthing resistance to protect 85% of the Winding Heglect the to reactance of the Stator winding in this case.
A single phase two wire a.c. Find the percentage saving in feeder copper if the system voltage is increased from 440 V to 1100 V. Assume same power is transmitted in both, same power loss and same power factor in both. I₁ I₁ 440V (a) 12 1100V 12 (b)
Three equal non-inductive resistances are connected in star across a balanced 400 V, 60 Hz system. A single phase wattmeter is connected on the system with its current coil in line 1 and potential coil in lines 1 and 3.This wattmeter registers 900 W. If the line 2 is accidentally open circuited, what will be the wattmeter reading under this condition?
An alternator is connected in star. If the phase voltage is 110 V, the line voltage is *
If R = 10 ohms and L = 0.05 henry are connected in series and energized by a 25 cycle sinusoidal voltage, the maximum voltage of which is 150 volts. Calculate the (a) impedance (b) instantaneous voltage (c) instantaneous current (d) instantaneous power (e) average power delivered to the load. Please answer asap thank you
Find phase difference of power supply voltage and vR(wich is equal to angle of current) In table 1
Answer all the questions Two watt-meter method is being used to measure power in a 3-phase 3-wire star-connected system with inductive load having 260V line voltage and 25 A phase current & phase angle of 45°. Calculate the total power consumed by the load. i) ii) Estimate the reading on each wattmeter.