Two power system areas operating at a nominal frequency of 60 Hz are connected with a tie line, and have the following characteristics: Area 1: R1 = 0.015 pu and D1 = 0.8 pu on a base of 1500 MVA Area 2: R2 = 0.03 pu and D2 = 0.9 pu on a base of 500 MVA The power flow direction on the tie line is from Area 1 to Area 2. Using a common base of 1500 MVA, what is the per-unit steady-state frequency change (Aw) for a load increase of 150 MW in Area 1? Select one: O a. 1.4822 x 10-³ pu O b.-0.8763 x 10-² pu O c. None of these O d. - 1.2677 x 10-³ pu

Two power system areas operating at a nominal frequency of 60 Hz are connected with a tie line, and have the following characteristics: Area 1: R1 = 0.015 pu and D1 = 0.8 pu on a base of 1500 MVA Area 2: R2 = 0.03 pu and D2 = 0.9 pu on a base of 500 MVA The power flow direction on the tie line is from Area 1 to Area 2. Using a common base of 1500 MVA, what is the per-unit steady-state frequency change (Aw) for a load increase of 150 MW in Area 1? Select one: O a. 1.4822 x 10-³ pu O b.-0.8763 x 10-² pu O c. None of these O d. - 1.2677 x 10-³ pu

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter7: Alternating Current, Power Distribution, And Voltage Systems

Section: Chapter Questions

Problem 8RQ

See similar textbooks

Similar questions

An ac resistance is higher than a dc resistance. True False
Match the following: (i) Hysteresis loss (a) Can be redud by constructing the core with laminated sheets of alloy steel (ii) Eddy current loss (b) Can be reduced by the use of special high grades of alloy stl as core material.
The principle operation of LVDT is based on the variation of Select one a. Self inductance b. Reluctance c. Mutual inductance d. Permanence
What will be the value of the twiddle factor: W42
Power factor PF PF=______________ Define the units of VA and VAR?
ings of a 40 kVA, 6 m respectively. The le- ate (i) the primary vol ced (ii) the full-load re
%VAI ۲,۷ K/s 9:- Zain 4.5G+ A step down de chopper is connected to an R-52 and L. 10 mH. The de supply voltage is 100 V. The chopper is switching at a frequency of 1 kHz with a duty cycle of 50%. Determine the load current, Jo and the peak to peak ripple current as an absolute value and as percentage of de value. ☐ О Δ
What is the difference between single-phase and three-phase alternating current? Select one: A. SINGLE-PHASE ALTERNATING CURRENT HAS THREE POWER LEGS WHILE THREE-PHASE ALTERNATING CURRENT HAS FOUR POWER LEGS B. SINGLE-PHASE ALTERNATING CURRENT HAS ONE POWER LEG WHILE THREE-PHASE ALTERNATING CURRENT HAS THREE POWER LEGS C. SINGLE-PHASE ALTERNATING CURRENT HAS TWO POWER LEGS WHILE THREE-PHASE ALTERNATING CURRENT HAS THREE POWER LEGS D. SINGLE-PHASE ALTERNATING CURRENT HAS TWO POWER LEGS WHILE THREE-PHASE ALTERNATING CURRENT HAS SIX POWER LEGS
A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
E2(V) 120V Test Open-circuit Short- circuit Primary 12(A) .29A 2A P2(W) 8.78W 13.4W 6.85V E1(V) P1(W) 7.69W 13.14W Test Open-circuit Short- circuit 11(A) .62A SA 48V 2.83V Normal 12 at E1 11 P1 E2 12 P2 120V 50.6V 48.42V 48.8V 49.33V 182A 4A 6A 815A 1A 1.22A 142A .2 4.75A 237.4W 56.5W 120.3V 1.31A 1.77A 2.28A 2.73A 3.26А 3.74A 119.6V 119.8V 120.6V 119.4V 120.6V 120.1V 119.9V 120.3V 219.1W 48.3W 72.39W 98.3W 120.1W 146.9W .4 81.2W 108.2W 130.5W 159.2W 184W 209.2W 237.5W .8 49.1V 1.2 1.4 49.83V 49.91V 50.1V 50.55V 170W 193.6W 219.1W 238.1W 1.6 4.23A 1.616A 1.8 4.74A 1.82A 2.0 50.3V 5.18A 258.3W 119.1V 2A 1) Calculate the turns ratio from the transformer primary/secondary voltage ratinga a= Using the open-circuit data at the primary and the short-circuit data at the secondary, calculate the four transformer parameters (to 3 significant figures) and fill in the following table. Parameter Rel Value(ohm) Xel Rc1 Xm1 Using the open-circuit data at the secondary and the short-circuit data at…
Task 3 A three phase, four wire star connected load consisting of: ZR: a resistor of 9500 in series with a 3H inductor ZB: a resistor of 1950 ZY: a resistor of 1950 in series with a 4µF capacitor Using the equipment available in the power lab (Room T017), connect the given load to a three-phase supply available in the lab and: 3.1. Determine the current of each line and the neutral current and measure the total power supplied by the source. 3.2. Analytically, calculate all currents and the total power and compare with those obtained in measurements. 3.3. Device a method and measure the waveform of the neutral current. Discuss the obtained waveform and the reason for any distortion in the waveform 3.4. Validate your calculations using computer simulation
Ip Ep=40 V f = 60 Hz N₂= 20- N₁ = 120 Find the maximum flux om om = Find the magnitude of the induced secondary voltage Es Es = units + Is Es units If the coefficient of coupling (k)= 0.75, determine the magnitude of the induced secondary voltage Es Esk=0.75 = units