Q2. In the following figure, the relationship between P and V was plotted at various temperature. The lower curves are for cooler temperatures than the upper ones. Describe the events at flattened lines as you go from left to right at: a. Temperature 274K b. Temperature 243 K

Q2. In the following figure, the relationship between P and V was plotted at various temperature. The lower curves are for cooler temperatures than the upper ones. Describe the events at flattened lines as you go from left to right at: a. Temperature 274K b. Temperature 243 K

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Part C 13.2 atm and -17 °C Express your answer with the appropriate units. HẢ Value Units %3D
5.- Nitrogen gas occupies a volume of 4.30 L at 54°C. If its volume increased to 7.80 L at the same pressure. Calculate the final temperature in kelvin. 235k 2k 593.163k 334.43k 200k
Calculate the final pressure of a sample of water vapor that expands reversibly and adiabatically from 75.5 torr and 250 cm3 to final volume of 2dm3 ?Take y=1.5. a. 7.5 Torr b. 15.5 Torr c. 3.322 Torr d. none of them
Given that for H,0,(g) → H,0(g) + ½ 0,(g), AH° = -106 kJ mol- !, and AS° = 58JK--mol', which ONE of the following statements is 1 TRUE? H,0,(g) is unstable at all A temperatures. H,0,(g) is stable at any temperature below 1827 K. H,0,(g) is stable at any temperature C above 1827 K. AG° = 123 kJ mol-1 for this reaction.
A balloon contains 230 g He at a pressure of 1 atm.the initial volume of the balloon is 1300 L.Rhe temperature increased by 10°C.Assuming at constant,pressure,what is the final volume of the balloon if ∆E IS 60.5 KJ?
Consider the problem of hammering a nail into a board. With due reqard for the hand holding the nail, place its pointed tip on the wood and strike it with a hammer. If the wood is hard so the nail does not go in easily, you will notice that the nail gets warm, especially after several strikes. We can figure out how much its temperature will rise by connecting what we know about Newtonian mechanics with what we are learning about temperature and heat. Let the nail have a mass of 50 g and strike it with one strong hammer blow. The hammer head has a mass of 0.5 kg (that's about 1 lb, so this is a good sized carpenter's hammer). Assume the impact velocity of the hammer on the head is 13 m/s and that it stops firmly at each blow. To make a reasonable assumption about the outcome, also assume that 75% of the energy of the hammer is converted into heat after the blow. The specific heat of the steel in the nail is about 482 J kg-1 K-1 . What is the temperature increase in the nail…
Determine the number of degrees of freedom (trans + rot) for each of the following gases; Ne, CO2, H2O. Then calculate the average total kinetic energy (per mole) at 25 celsius for each gas. (R=8.314J K-1 mol-1)
7. When detern ing the mass of a liquid, ras in a hurry and did not allow enough time for the temperature of the flask to reach the temperature of the boiling water bath. The student recorded the temperature of the gas as 100.0°C when it was only 80.0°C, Is the molar mass calculated by the student higher or lower than the accepted molar mass, or does this error have no effect on the calculated result? Briefly explain your answer # 2/HB Office DEPOTS b) If the student assumed the volume of the flask was 125 mL (as marked by the side of the flask) rather than measuring the volume experimentally, would the unknown's calculated molar mass be too high, too low, or unaffected? Explain. # 2/HB 4
A mixture of gaseous reactants is put into a cylinder, where a chemical reaction turns them into gaseous products. The cylinder has a piston that moves in or out, as necessary, to keep a constant pressure on the mixture of 1 atm. The cylinder is also submerged in a large insulated water bath. (See sketch at right.) 1 atm pressure piston cylinder From previous experiments, this chemical reaction is known to absorb 257. kJ of energy. water bath gases The position of the piston is monitored, and it is determined from this data that the piston does 231. kJ of work on the system during the reaction. exothermic Is the reaction exothermic or endothermic? endothermic up Does the temperature of the water bath go up or down? down neither in Does the piston move in or out? out neither in Does heat flow into or out of the gas mixture? out neither How much heat flows? Be sure your answer has the correct number of significant digits.
A sample of H2 gas has a pressure of 1.2 atm at 25°C. If the pressure has increased to 1.5 atm at constant volume and amount of gas, 6. compute for the new temperature in Kelvin.
Rank the following temperatures in order of increasing kinetic exgergy (speed). 50 °C 150 °C 0 °C 20 °C
2.00-mol of a monatomic ideal gas goes from State A to State D via the path A- > B-> C-> D: State A PA = 11.0atm, VA = 13.50L State B PB = 11.0atm, VB = 6.00L State C PC = 25.0atm, VC = 6.00L State D PD = 25.0atm, VD = 20.50L Assume that the external pressure is constant during each step and equals the final pressure of the gas for that step. Calculate q for this process.