Q2. B. The single-phase H-bridge inverter is operated in the quasi-square-wave mode at the frequency f= 100 Hz, with phase shift ß between half-bridge output voltages va and vb. The load is an RL load with R=-10 2 and L=20 mH. (i) Find ß so that the fundamental amplitude of the load voltage v, is 200 V. (ii) For ß= n/2 sketch v, and i, (approximately). (iii) For ß= n/2 find the total average power supplied to the load.

Q2. B. The single-phase H-bridge inverter is operated in the quasi-square-wave mode at the frequency f= 100 Hz, with phase shift ß between half-bridge output voltages va and vb. The load is an RL load with R=-10 2 and L=20 mH. (i) Find ß so that the fundamental amplitude of the load voltage v, is 200 V. (ii) For ß= n/2 sketch v, and i, (approximately). (iii) For ß= n/2 find the total average power supplied to the load.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

W Q.2) A Full-wave bridge rectifier with a (400 Sin(100)t) sinusoidal input has a load resistor of (10KS) .Sketch Vo and determine the : 1- Fi and Fo So 2- Vdc 2%. 〃 3- Vrms 4- Irms 5- Prms 6- Pdc PHO 7- Efficiency 8- Ripple Factor 9- PIV (.
Exercise_4 A single-phase controlled rectifier bridge consists of one SCR and three diodes feed R-load: a) Draw the circuit diagram of this bridge rectifier b) Sketch output voltage waveform for a firing angle a for the SCR and hence obtain an expression for the average output voltage under the assumption of constant current. Show the conduction of various components as well. Draw waveforms of current through TI, D1, D2 and D3 assuming constant load current. c) d) For an AC source voltage of 230 V, 50 Hz and firing angle of 45°, find the average output current and power delivered to 1000 resistor. O
Consider the half-wave rectifier shown below. It needs to deliver 0.1 A and an average of 15 V to a load. The source is 60 Hz and the diode has a 0.7 V drop. The allowable ripple is no more than 0.4 V (2.5%). Find: Peak AC voltage Vm of the source a) b) The minimum value of the smoothing capacitor(s) c) Comment on the type of capacitor and its/their values you would use for this amount of capacitance vs(t) K Load UL
A half-wave rectifier circuit has an input voltage of 60V for the entire swing of the input signal from the secondary winding of the transformer. If the load resistance is 900 and a shunt capacitor is connected therein: 1. Draw the circuit 2. Solve the following unknown values. a. The peak voltage V b. the average output voltage Volave) c. the average load current lolavel, d. the rms load voltage Volcms), e. the rms load current loma) f. the ripple factor RF of the output voltage, g. the rms ripple voltage Vrirms) h. the average diode current ID(ave) i. the rms diode current Ipicms), j. the peak inverse voltage PIV of the diode, k. the average output power Polac 1. the DC output power Po(de) m.the frequency fr of the output ripple voltage, n. the input power factor PF.
In the following circuit, the nMOS has a threshold voltage of Vr = 1.0 Vand K = 2 mA/VÅlso given that R1 = 3 kNVpp identical with vp. = 0.9(i.e. use CVD model for the diodes). Our task is to set the value of Rp such that the MOSFET will be operating at the edge of saturation. What's edge of saturation? We know in the triode region vps vGs – VrHence, the edge of saturation means when vps = vGS - VAt this mode, both the equations for In in saturation mode and triode mode would give the exact 6 Vand the diodes are same result, VDD VDD Rp R1 KIKKH
What is the maximum value of vs(i.e.vsm ) Find the peak-to-peak ripple voltage vr Find the average output voltage Vo in steady state Find the average diode current ID in steady state. If the secondary winding resistance of the transformer is 1.5 Ω, calculate the maximum surge current in the worst-case scenario
4. An RC filter stage (R = 33 0, C = 120 HF) is used to filter a signal of 24 V dc with 2 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 100-mA load. Also calculate the ripple of the filtered signal applied to the RC stage. *****END*****
A silicon controlled rectifier (SCR) has a forward breakdown voltage of 230 V. When a gate current of 2 mA flows in the gate circuit. If a sinusoidal voltage of 400 V peak is applied, find the following: Firing angle. Average output voltage. Average current for a load resistance of 180 Ohms. Power output
If the load resistance of a capacitor-filtered full-wave rectifier is increased, the ripple voltage Select one: a. increases b. doubled c. has different frequency d. not affected e. decreases
. A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 300 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?
8-The waveform of output voltage of half-controlled three phase bridge rectifier in each cycle contains: Two- pulse six- pulse three- pulse 9-The DC supply voltage of single phase bridge inverter is 300V. For quasi-square wave output voltage with a 60 percent ON time, the RMS value of output voltage is: 232.37V 220.5V 270.9V 10-For three phase bridge inverter with 120° conduction and resistive star-connected load, the waveforms of: (a) The load current and line voltage are quasi-square. (b) The load current is quasi-square and line voltage is a six- step. (c) The load current is six- step and line voltage is quasi-square. 9.
A half-wave rectifier circuit has an input voltage of 60V for the entire swing of the input signal from the secondary winding of the transformer. If the load resistance is 9on and a shunt capacitor is connected therein: 1. Draw the circuit 2. Solve the following unknown values. a. The peak voltage Vm b. the average output voltage Volave) c. the average load current Iolauel, d. the rms load voltage Vojcmal, e. the rms load current Iotms) f. the ripple factor RF of the output voltage, g. the rms ripple voltage Vrima) h. the average diode current I Diave) i. the rms diode current Ipicmsi, j. the peak inverse voltage PIV of the diode, k. the average output power Polac I. the DC output power Potdc) m.the frequency fr of the output ripple voltage, n. the input power factor PF.