A half-wave rectifier circuit has an input voltage of 60V for the entire swing of the input signal from the secondary winding of the transformer. If the load resistance is 900 and a shunt capacitor is connected therein: 1. Draw the circuit 2. Solve the following unknown values. a. The peak voltage V b. the average output voltage Volave) c. the average load current lolavel, d. the rms load voltage Volcms), e. the rms load current loma) f. the ripple factor RF of the output voltage, g. the rms ripple voltage Vrirms) h. the average diode current ID(ave) i. the rms diode current Ipicms), j. the peak inverse voltage PIV of the diode, k. the average output power Polac 1. the DC output power Po(de) m.the frequency fr of the output ripple voltage, n. the input power factor PF.

A half-wave rectifier circuit has an input voltage of 60V for the entire swing of the input signal from the secondary winding of the transformer. If the load resistance is 900 and a shunt capacitor is connected therein: 1. Draw the circuit 2. Solve the following unknown values. a. The peak voltage V b. the average output voltage Volave) c. the average load current lolavel, d. the rms load voltage Volcms), e. the rms load current loma) f. the ripple factor RF of the output voltage, g. the rms ripple voltage Vrirms) h. the average diode current ID(ave) i. the rms diode current Ipicms), j. the peak inverse voltage PIV of the diode, k. the average output power Polac 1. the DC output power Po(de) m.the frequency fr of the output ripple voltage, n. the input power factor PF.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Related questions

Q: The input to a full-wave rectifier is 30 V AC (RMS). The load resistor is 10 ohms. The DC power at…

Q: A 60 Hz sinusoidal voltage with an RMS value of 240 V is applied to a single-phase full-wave SCR…

A: The rms output voltage of a full wave scr rectifier is given it is asked to find the firing angle in…

Q: In the full-wave rectifier circuit, the transformer has a turn ratio of 1:2. The transformer's…

Q: The Circuit Below shows a basic Buck-Boost Converter with a highly inductive Load. With a Deliberate…

A: In the given circuit firstly we have to find the duty cycle Duty cycle = 0.55+17×0.2100Duty cycle…

Q: A 60 Hz sinusoidal voltage is applied to an SCR full-wave rectifier. If the DC output voltage is 74…

Q: the full-wave rectifier circuit of figure , the transformer has a turns ratio of 1:2. The…

Q: A 60 Hz sinusoidal voltage is applied to an SCR full-wave rectifier. If the DC output voltage is 58…

A: The average dc output voltage of the full-wave SCR rectifier is given by the expression as shown…

Q: The input to a full-wave rectifier is 10 V AC (RMS). The load resistor is 10 ohms. The DC voltage at…

A: Given, input AC voltage, VRMS=10 V load resistor, RL=10 Ω

Q: A 60 Hz sinusoidal voltage with an RMS value of 120 V is applied to a single-phase full-wave SCR…

Q: The full wave rectifier in the circuit below is to deliver 0.25A and 15V (peak) to a load. The…

A: Given data: IDC=0.25 AVL=15 VVp=120 VVγ=0.7 VVp-p=0.4 V

Q: For the given circuit below, a step down transformer gives an RMS voltage of 230 V/ 15.2- 0-15.2 V…

A: Peak inverse voltage of diode? This circuit is centre tap. Full wave rectifier

Question

A half-wave rectifier circuit has an input voltage of 60V for the entire
swing of the input signal from the secondary winding of the
transformer. If the load resistance is 900 and a shunt capacitor is
connected therein:
1. Draw the circuit
2. Solve the following unknown values.
a. The peak voltage V
b. the average output voltage Volave)
c. the average load current lolavel,
d. the rms load voltage Volcms),
e. the rms load current loma)
f. the ripple factor RF of the output voltage,
g. the rms ripple voltage Vrirms)
h. the average diode current ID(ave)
i. the rms diode current Ipicms),
j. the peak inverse voltage PIV of the diode,
k. the average output power Polac
1. the DC output power Po(de)
m.the frequency fr of the output ripple voltage,
n. the input power factor PF.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Three Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the difference between a diode and rectifier?
What is CEMF?
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
A fully controlled, single-phase bridge rectifier is powered from an ideal 220V, 50Hz source. The rectifier is triggered with a trigger angle of 60 degrees and provides a smooth current of 50A to the load at the output. According to this: a) Draw the waveform of the output voltage in scale and calculate the average value of the output voltage. Combine the average voltage signal with the output voltage wave signal. Show on the same figure. b) Draw the waveforms of the thyristor currents, the gap diode current and the current drawn from the source in scale. c) Calculate the value of the filter inductance used at the output when the ripple in the load current is 3A. (Do the operations by showing the output voltage shapes and areas on the figure. The answers should be in the system and order in the solved examples.)
A half-wave rectifier is to provide an averagevoltage of 50 V at its output.a. Draw a schematic diagram of the circuit.b. Sketch the output voltage waveshape.c. Determine the peak value of the output voltage. d. Sketch the input voltage waveshape.e. What is the rms voltage at the input?
3. For the half-wave rectifier given in the figure below, find the average values ofthe output voltage and current, and the ripple factor of the output voltage.
The Figure 2 shows an electronic circuit designed for supplying power to a load (R1). The supply voltage 235V (RMS, AC) at frequency of 50HZ. The required DC voltage and power for the load are 24V and 3.6 W respectively. The Electrical Components of this AC to DC converter are: A full-wave rectifier to convert AC voltage to DC voltage. A regulator with transistor and Zener diode to ensure a constant voltage and power for the load. D1 Iide 91 Vaut VLoad D2 D3 Vde VI sine R1 RL Regulate Reetifier Figure 2. Complete Circuit Assume that the diodes are real diodes (NOT ideal diodes). The following information is available: The collector to base resistor of the regulator R1 = 5.0 k The transistor Q1 with B value of 24 is used for the regulator circuit. Determine the following quantities for this electronic device and fill the table below: Question Answer The voltage of Zener Diode (Vz) The current in R1 The DC current into the regulator | (Idc) Base current of transistor (IB) Collector…
A three phase fullwave controlled rectifier has an input voltage which is 480vrmsat 60hz. the load modelled as a series resistance and inductance with R=10ohm and l=50mH. determine the delay angle to produce an average of 50ain the load.
Consider the half-wave rectifier shown below. It needs to deliver 0.1 A and an average of 15 V to a load. The source is 60 Hz and the diode has a 0.7 V drop. The allowable ripple is no more than 0.4 V (2.5%). Find: Peak AC voltage Vm of the source a) b) The minimum value of the smoothing capacitor(s) c) Comment on the type of capacitor and its/their values you would use for this amount of capacitance vs(t) K Load UL
A three phase full wave rectifier is shown below along with peak phase voltage Vm-169.7V. The load is purely resistive. The rectifier delivers Ipc = 100 A and the source frequency is 60 Hz. The DC output voltage is %3D VDc=280.7V and the output RMS voltage is equal to VRMS=280.93V. The efficiency, FF and RF are respectively equal to: Secondary D D D, R AD. Z D. D, Select one: O a. 99.83%, 100.08%, 4% O b. 99.83%, 55.08%, 4% O C. 99.83%, 100.08%, 16% O d. 87.83%, 100.08%, 4%
Consider a peak rectifier ted by a 50 Hz sinusoid having a peak value Vp-100 V. Let the load resistance R 10 kohm. The value of the capacitance C that will result in a peak to peak ripple of 3 V is:
LR phase shift control is used in a controlled rectifier. If the value of the inductor is 100 mH, find the minimum and maximum value of the control resistor if the ratio of Idc/Idcmax is to be 0.1 to 0.9.