8-The waveform of output voltage of half-controlled three phase bridge rectifier in each cycle contains: Two- pulse six- pulse three- pulse 9-The DC supply voltage of single phase bridge inverter is 300v. For quasi-square wave output voltage with a 60 percent ON time, the RMS value of output voltage is: 232.37V 220.5V 270.9V 10-For three phase bridge inverter with 120° conduction and resistive star-connected load, the waveforms of: (a) The load current and line voltage are quasi-square. (b) The load current is quasi-square and line voltage is a six- step. (c) The load current is six- step and line voltage is quasi-square. 9.

8-The waveform of output voltage of half-controlled three phase bridge rectifier in each cycle contains: Two- pulse six- pulse three- pulse 9-The DC supply voltage of single phase bridge inverter is 300v. For quasi-square wave output voltage with a 60 percent ON time, the RMS value of output voltage is: 232.37V 220.5V 270.9V 10-For three phase bridge inverter with 120° conduction and resistive star-connected load, the waveforms of: (a) The load current and line voltage are quasi-square. (b) The load current is quasi-square and line voltage is a six- step. (c) The load current is six- step and line voltage is quasi-square. 9.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2. Given the circuit a. State how each switch can be realized using transistors and/or diodes, and whether the realization requires single-quadrant, current/voltage bi-directional two quadrant switch or four quadrant switches then redraw the circuit. b. Solve the converter to determine the inductor currents, capacitor voltages and conversion ratio. Ignore all losses.
I need the answer as soon as possible
In a full wave bridge rectifier, the transformer secondary voltage is 20sinwt. The forward resistance of each diode is 25N and load resistance is 1.5K2. Calculate, i. Im ii. Idc iii. Pdc iv. Рас v. n
In a rectifier circuit , DC output voltage and RMS output voltage is 0.3 V & 0.49 V respectively. The form factor of this circuit is ___________________. a. 1.63 b. 3.27 c. 0.61 d. 1.17
Calculate the capacitor value Conditions: 1st That, for the calculation of the peak voltage of the rectifier output, it is 9V. 2nd That the ideal ripple voltage is equal to 10% of the peak voltage at the output of the rectifier. 3rd That the maximum load current is 0.009A
s/ Introduction to Electronic Analysis and Design - CE255/EE255 - 01 - Spring : One of the disadvantages of the Full-wave 2-diode rectifier circuit is Select one: a. it reduces the output with double the forward diode voltage drop. b. PIV equals to the supply voltage c. the need to use a center-tapped transformer.
iv. For six-phase half-wave rectifier circuit, the preferred circuit from the point of harmonics reduction in the supply currents is: (a) Simple six-phase half-wave circuit. (b)Double-star six-phase half-wave circuit. (c) Six-phase fork connection circuit. v. The DC supply of single phase bridge inverter is 350V. For quasi-square wave output voltage with a 70 percent ON time and frequency is 50HZ, the RMS value of output voltage is: (a) 292.8V (b) 220.5V (c) 250.6V
A sinusoidal voltage of 48v, 60 Hz is applied to a half-wave rectifier with dynamic resistance of the diode of .001ohms turns ratio (3:1). Calculate the DC and RMS currents flowing through the load(R=210 ohms). Also calculate the dc output power developed, ac – input power supplied, rectification efficiency, and ripple factor.
2. A circuit of 3-Phase Controlled Half Wave Rectifier with Resistive load is as below. A T2 eleeeeee B If the firing angle, a are to set at r/9, complete the circuit operation for the whole cycle (0° to 360°) for the period stated in Table 1. By using appropriate scale, draw a waveform of Average Output Voltage, Vo(avg). Derive an equation for the average output voltage, Vo(avg). If the rectifier is connected to 208V, calculate the Vo(avg) if the load is purely resistive. (C3, CLO1) Duration Period s1 S2 S3 Vout 1 0° – 20° 20° – 50° 3 50° – 120° 4 120° – 140° 140° – 170° 170° – 240° 7 240° – 260° 8 260° – 290° 290° – 360° Table 1
Design Half-wave Rectifier Circuit to provide an output of 100 VDC. Then calculate its transformer peak voltage rating, the diode PIV rating, and the transformer turns ratio, if the power is taken from the 220V line AC supply
6. A halfwave rectifier(HWR) has an AC input of 14.14Vrms. A Si diode rectifier is connected such that it will conduct during the negative half cyle while a 5K ohm resistor is connected in parallel with the output (Vo).
HW: For full wave 3phase rectifier, if the output de current equal to (31.061A) and the load resistance (20 2).find the input Vma voltage ( phase to ground).