Q2.) A CRT has deflecting plats of 6mm longs, and 2000μm a part. The screen is 500mm away from the center of plates. The electron beam enters the plates at velocity of (2445x10 m/s). An input voltage signal of 110mV is applied to the CRT whose amplifier has an overall gain of 100. If the electrons mass and charge is 9.11x10-28g, 1.6x10¹⁹C respectively. Determine: 1) The deflection on the screen (D). 2) The angular deflection (0). 3) The deflection factor (G).

Q2.) A CRT has deflecting plats of 6mm longs, and 2000μm a part. The screen is 500mm away from the center of plates. The electron beam enters the plates at velocity of (2445x10 m/s). An input voltage signal of 110mV is applied to the CRT whose amplifier has an overall gain of 100. If the electrons mass and charge is 9.11x10-28g, 1.6x10¹⁹C respectively. Determine: 1) The deflection on the screen (D). 2) The angular deflection (0). 3) The deflection factor (G).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw the wave shape of the output voltage (VOUT) of the following circuit. Assume both theSilicon zener diode breakdown voltage to be 10V & peak input voltage VP to be 20V.
2. Plot the transfer function, and clearly indicate the on/off conditions of each diode, the slope of the line, and the voltages of turning points in each operating region for the following circuits. Assuming the constant-voltage model (VD,on = 0.8 V) is used to determine the DC level. Also, Plot the output waveform in time-domain if the input signal is as shown below with the amplitude and other important values labeled in the figure. (a) (b) Vin R= 500 D₁ V₁= 2.5 V D₂ A V₂ 1.6 V D₁ 2R 2X4 2R D₂ 3R out Vout Vin Vin 10 mv 1-AAAA-3.4 V >t 5 V
When a p-and n-type semiconductor are joined at an interface their Fermi energies equilibriate. If we extend this thinking and apply it to an interface between a metal and (p-or n-type) semiconductor to make a metal-semiconductor heterojunction, what will the expected outcome be? Use diagrams and words to explain.
Assume now that the diode D1 is forward biased. Represent the diode with the constant voltage drop model (0.7V) and determine the expression (or value) for the voltage that appears across the diode, VD. This gives you the other part of the transfer function.
INCLUDE ALL THE DECIMALS
Answer all subparts for like either dislike....
04:- Design a bias circuit for NPN silicon transistor having a nominal B-100 to be used in voltage divider circuit with Q-point of Ic 10 mA and VCE = 10 V. Use standard valued 5% resistors and draw a schematic diagram of your design. (10 points)
6. For a particular dual-slope ADC: Vref = +5.0V and the charge time is 6ms. %3D a) " Draw a time-domain plot for the dual-slope ADC. b) When Vin = -2.5V, what is the total conversion time? c) When Vin increases by 1.0V, what is the total conversion time?
Subject: Electronics Engineering Solve no 6
a) Draw the energy band diagram of a MOSFET transistor, when -5 volts are applied to the drain contact. b) Explain what will happen to the Fermi level at the source contact and the drain contact in the following scenarios (Use an appropriate energy diagram to illustrate your answer): A positive voltage is applied to the drain contact. A positive voltage is applied to the source contact. c) Explain why current flow in a MOSFET transistor. Use a diagram to illustrate your answer.
a ): The depletion region is a layer of positive and negative charge in the semiconductormaterial Briefly explain how the depletion region formed in the semiconductormaterial after the PN junction is created.b): An audio signal amplifier is used to reproduce input audio signals at sound-producoutput elements, with desired volume and power levels. What is the function of volumecontrol and power amplifier in an audio signal amplifier ?
Explain this diagram