Q2/ Asphase. 6.6 KV, 6-pole, 50 Hzy A-Conr. S.M has I Z= o+j 30 r/phose, take 100A of 0.9 leading Pif Current Neglect losses. Fil: @cf@load angle in mechanical degrees Tr. what increase in excitation is required to sustain a torque overload of 2500 μm without falling of synchronism. with this excitation what would be The Values of current, P.F, 5 at vated torque with this excitation what reduction of 6 terminal voltage would be permissible to just keep The motor in synchronism at rated torque,

Q2/ Asphase. 6.6 KV, 6-pole, 50 Hzy A-Conr. S.M has I Z= o+j 30 r/phose, take 100A of 0.9 leading Pif Current Neglect losses. Fil: @cf@load angle in mechanical degrees Tr. what increase in excitation is required to sustain a torque overload of 2500 μm without falling of synchronism. with this excitation what would be The Values of current, P.F, 5 at vated torque with this excitation what reduction of 6 terminal voltage would be permissible to just keep The motor in synchronism at rated torque,

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.3P: Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source...

See similar textbooks

Similar questions

Which of the following sensors has a permanent magnet inside? Hall effect sensor thru-beam optical sensor piezo-electric sensor LVDT capacitive proximity sensor |o|0|0|6
I need the answer at 20 minute
Construct the circuit in Figure 1 in the Circuit JS simulator. Note that the voltage source is given in RMS. Within Circuit JS while defining the max voltage of the voltage source include “rms” after the number to tell Circuit JS that this is a rms value. Also note that there are additional parameters when instantiating a transformer in Circuit JS. Leave these at the default values. Additionally, transformers may have problems simulating in Circuit JS. Answer the following: 1. From the simulation results, determine the power dissipated in R2 and compare to the expected value from the previous section.2. Change the transformer ratio (“Ratio” as a fraction when you “Edit…” the transformer component) to the value calculated in the previous section to provide maximum power transfer in R2. Note: In Circuit JS, Transformer Ratio = Primary/Secondary.3. Rerun the simulation, calculate the power dissipated in R2 and compare to the expected value from the previous section.4. Change the…
GENERAL RLC CIRCUITS: Solve and show your solution completely. Make sure your answers are in 4 decimals places. The ohmic resistance of a large magnetic contactor is measured to be 20 ohms. A 230 V 60 Hzis impressed upon the contactor and the current is taken as 3.2 amperes. Neglecting core loss,determine the inductance of the contactor in mH.
Fundamentals Of Energy Systems HW 6 Q4
Design a flyback converter for an input of 24 V and output of 40 W at 40V. Specify the transformer turns and magnetizing inductance, switching frequency and capacitor to limit the ripple voltage less than 0.5%.
The impedance ZL in the circuit shown in Figure is adjusted for maximumaverage power transfer to itself.(a) What should be the value of ZL?(b) What is the maximum average power delivered to ZL?(c) What percentage of the average power delivered to the linear transformer is delivered to ZL?
Can you solve D and E
A 250/125 V, five kVA single-phase transformer has a primary resistance of 0.2 ohms and reactance of 0.75 ohms. The secondary resistance is 0.05 ohm and reactance of 0.2 ohms.a) Determine its regulation while supplying full load on 0.8 leading p.f.b) The secondary terminal voltage on full load and 0.8 leading p.f.Ans.: -0.4.88%; 131.1
Fundamentals of Energy Systems HW5 Q5
Q.4/ choose true or false: 1. The reluctance of any core is proportional directly with the length of it and inversely with both the permeability and the cross-section area of it. 2. The number of parallel paths in wave windings is equal to twice of the number of poles. 3. In dc machines with same values of Z, N, Ø, the emf for wave winding type is more than emf of lab winding type. 4. If we insert a current in such a conductor subjected to a constant magnetic field, a movement will achieved giving the principle of electric generator.
A Cockcroft-Walton type voltage multiplier has ten stages with capacitances, all equal to 0.1 μF. The supply transformer secondary voltage is 100 kV at a frequency of 60 Hz. If the load current to be supplied is 5 mA, find (a) the percentage ripple, (b) the regulation, and (c) the optimum number of stages for minimum regulation or voltage drop.