Q2/ A force P = 1 KN applied to a right bar suspended by three wires, as shown below. all wires are of equal size and the same material. for each wire, A = 80 mm , E =200 GPa , and L =4 m. If initially, there were no slack in the wires, how will the applied load distribute between the wires? 200 100 100 4000 mm mm mm mm

Q2/ A force P = 1 KN applied to a right bar suspended by three wires, as shown below. all wires are of equal size and the same material. for each wire, A = 80 mm , E =200 GPa , and L =4 m. If initially, there were no slack in the wires, how will the applied load distribute between the wires? 200 100 100 4000 mm mm mm mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Rigid bar ABCD is loaded and supported as shown. Steel [E = 30800 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.78 in.2 and bar (2) has a cross-sectional area of 0.32 in.2. After load P is applied, the strain in bar (1) is found to be 610 μεμε. Assume L1=50 in., L2=76 in., a=28 in., b=21 in., and c=22 in. Determine:(a) the stresses in bars (1) and (2).(b) the vertical deflection vD of point D on the rigid bar.(c) the load P.
A steel bar having 65mm*65mm*3000mm dimension is subjected to an axial force of 128 kN. Taking E=2*105N/mm2 and m = 0.3, find out Change in dimensions (height, width and length), Change in volume and Volumetric Strain
Q1
Need CF and CD
Figure 2 shows a bar with a length L fixed at the left end. Question 2 The uniformly distributed force f (unit: N/m) is applied along the axis of the bar, and a concentrated force P (unit: N) is applied at the free end of the bar. The bar has a constant Young's modulus E and cross-section area A. Find the stretch of the bar: (a). at the free end of the bar; (b). at the center of the bar. (Expressing all the resulta with E, A, L, f, and P). E, A L Fig. 2. The kft end of the bar is fd, ad the froe ed of the bar is applied with a force P. The uniformly distribatod kece f is applied akong the ais of the bar.
Consider the steel truss and member cross-section presented in figures below. All the members of the truss have the same cross-section as shown in the figure to the right. They all also have a Young's Modulus of 210 GPa. What can the highest value of force F be before member AC fails by buckling? Force 1AN - 300 mm 40° 4 m $35 mm 7m 300 mm 8 m 35 mm 35 mm 35 mm Please provide your answer in kN.
AL: 1₂ The above figure (not drawn to scale) shows a rod made up of two cylindrical sections of the same material. The left cylinder has diameter d, = 30mm and length 4 = 150mm. The right cylinder has diameter dy=10mm and length = 150mm. The rod is subjected to a force F = 50KN. Find the total extension in the rod, AL, given that E = 203kN/mm². Enter your answer in mm to 5 decimal places in the box below: mm -F
A uniform stone slab weighs 400 lb and is suspended by 3 cables and subjected to a downward vertical load as shown in the figure and parameter table. A B F parameter L1 L2 L3 value units 2 ft 4 ft 3 ft F 150 lb The tension in cable A is 200 * lb The tension in cable Bis 35.7 X lb The tension in cable C'is 314 X lb
Question 4 The round tapered brass bar, in Figure Q4, of length 500 mm is subjected to loads. Determine the change in length if E = 1x10ʻ kg/em². 300kg 500 kg 10 mm 4 700 kg 20 mm 500kg -150- -150 200 mm m m Figure Q4: Bar subjected to various forces
Last 2 digits 71 P N
250 mm Q1: The beam shown in Figure 1 is subjected to a vertical force Py and a horizontal force Pr The data for P Pr, a L,and e are shown in Table1. Determine the maximum compressive and tensile stresses under the vertical force (at a distance a from the left support.) Pv > 135 KN 55 omm a I=> 6omm Ph 2248KN 120 mm L =2 600mm Figure 1