P = 30 kNQ1/ Two solid cylindrical rods are joined at B and loaded as shown. Rod AB ismade of steel (E=200 GPa) and rod BC of brass (E =105 GPa). Determine (a) the30 mm250 mmtotal deformation of the composite rod ABC, (b) the deflection of point B.40 kN300 mn50 mm

Given data: Modulus of elasticity of steel rod AB, Est = 200 GPa. Modulus of elasticity of brass…

Q1/ Two solid cylindrical rods are joined at B and loaded as shown. Rod AB is made of steel (E=200 GPa) and rod BC of brass (E =105 GPa). Determine (a) the total deformation of the composite rod ABC, (b) the deflection of point B.

Q1/ Two solid cylindrical rods are joined at B and loaded as shown. Rod AB is made of steel (E=200 GPa) and rod BC of brass (E =105 GPa). Determine (a) the total deformation of the composite rod ABC, (b) the deflection of point B.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1) A steel bar of 15 mm in diameter was bent as shown. Using the method of work and energy, determine the defiexion at the C end, due to the force of 200 N
Please box the final answer. Thank you
Question 2 The rods BE and CD are made from steel (E=200 GPa), and each have a diameter, P. The ends of the rods are threaded with a pitch, p. The nuts at B and C are initially finger tightened such that they barely touch rigid member ABC. If the nut at C is then tightened by one full turn, determine: (a) the tension in rods BE and CD (b) the distance, uc, that point C on the rigid member ABC moves. Assume a=300 mm, b= 100 mm, c= 2.5 m, d= 6 m, 0=40 mm, and p=1 mm. OA a В E b D C d
1. A cantilever of square cross section as shown was made of mild carbon steel SAE 1020, as rolled, and was designed to support a static load W = 15 lb. After the beam was installed, it was discovered that the weight W was not static but vibrated, so that actually the beam was subjected to a repeated load. Measurement showed that the weight rose and fell a distance h equal to 0.05 inch. Shortly thereafter the beam fractured at the fillet which had a machined radius of 1/32 in. (a) Make calculations to show and state your conclusion whether or not the beam should have been expected to fail. (b) for the same data, design a new cantilever with the same dimensions except with a fillet radius r= 1/8 in. Determine whether a carbon steel would be necessary, and if so, its SAE or AISI no. 1/2" 3/4". 6"
A solid brass [E = 93 GPa] axial member is loaded and supported as shown. Segments (1) and (2) each have a diameter of 23 mm and segment (3) has a diameter of 12 mm. Assume L₁ = 1.9 m, L₂= 1.3 m, L3 = 1.7 m, R = 36 kN, Q = 12 kN, and P = 24 kN. Determine: (a) the deformation of segment (2). (b) the deflection of joint D with respect to the fixed support at A. (c) the maximum normal stress in the entire axial member. (1) A L₁ R (2) L2 L3 (3) D P B C
A square column with side dimension of 50 mm rests on top of a timber footing. It is determined that the column carries an axial load of 417 kN. If the punching strength of concrete is 10.05 MPa, determine the minimum thickness (mm) of the footing.
3(a). Both portions of the rod ABC are made of an aluminum for which E= 60 GPa. Knowing that the magnitude of P is 3 kN, determine (a) the value of Q so that the deflection at A is zero, (b) the corresponding deflection at B. Figure 3 1.5mm diameter 1.0⁰m 50-mm diameter WSTE
6) The assembly consists of two posts AB and CD made from material 1, having a modulus of elasticity E, and each cross-sectional area A₁, and a central post EF made from material 2, having a modulus of elasticity E2 and each cross-sectional area A₂. If the posts AB and CD are to be replaced by those having a material 2, determine the required cross-sectional area of these new posts so that both assemblies deform the same amount when loaded. ↓ B d E F d L D
A frame ABC consists of a horizontal beam BC which is supported by a round solid rod AB inclined at a 50° angle, as shown below. The ends of the rod AB are flattened to make pin connections at A and B. A vertical load of 5,000 N is acting at the mid-length of the beam. The rod material is a steel with modulus equal to 207 GPa and yield strength of 220 MPa. (a) Using a factor of safety of2.5, determine the diameter of the rod AB. (b) If a clevis joint is used at the pin connection at B, design the pin diameter so that it does not fail in shear. The tensile yield strength of the pin material is 300 MPa. Use a factor of safety between 1.5 and 2.5. 5,000 N В C 5 m 3 m 50° A
Members AB and BE of the truss shown consist of 25-mm-diameter steel rods (E = 200 GPa). It is given that P = 81 kN. Determine the elongation of rod BE. The elongation of rod BE is ___ mm.
Solve step by step and explain each step. and please not copy paste previously answer .
A 15 mm diameter steel bar was bent as shown. Using the work and energy method, determine the deflection at end C due to the force P of 200 N. Use E = 200 GPa and G = 77 GPa. B 250 mm 250 mm A P = 200 N C