Q1/ If the beam has a square cross section of 11 in. on each side and subjected loading shown below, determine:- 1- Draw Shear force and bending moment diagrams of the beam. 2- The absolute maximum shear stress developed in the beam. 3- Draw the distribution of shear stress over the cross section at the location of the maximum shear stress.

Q1/ If the beam has a square cross section of 11 in. on each side and subjected loading shown below, determine:- 1- Draw Shear force and bending moment diagrams of the beam. 2- The absolute maximum shear stress developed in the beam. 3- Draw the distribution of shear stress over the cross section at the location of the maximum shear stress.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2.
Problem 4. Determine the value of the constant C in the stress function 0 = C{r?(x -0) + p?sin 0 cos 0 - r? cos? 0 tan a required to satisfy on the upper and lower edges of a triangular plate shown below. Evaluate the stress components o, Ty for a vertical section mn. Draw curves for the case a = 20° and draw also for comparison the curves given by elementary beam theory. m a y
From the given three reservoirs, the elevation of A is 345m, B is at elevation 300m, and C is at elevation 240m. The rate of flow at 1 is 300li/sec. A. Compute the headloss in pipeline 2 B. Compute the discharge in pipeline 3 C. Compute the diameter of pipeline 3 Location of pipe Reservoir A to junction X Length (m) 600 Pipe no Diameter (mm) HAZENS (C) 1 450 120 Junction X to Reservoir B 2 3600 300 100 Junctin x to Reservoir C 3 1250 ? 110
Since the bending safety stress σem = 10 MPa, shear safety stress Tem = 600 kPa of the rectangular section beam given the loading status in the figure and width b = 150 mm, how much should the height h of the beam section be at least so that the stresses that will occur in the beam do not exceed the safety stress values. .
2
3. In the figure shown: a) Draw the Shear and Moment Diagram, and determine the maximum moment. b) Determine the Maximum Tensile and Maximum Compressive Flexural Stress developed. P1 27 kN P2 11 kN A 225 mm P2 3m 3m W
QUESTION 3) A horizontal beam AD is supported by an inclined strut CB and carries a load of 15 kN at joint D in the figure. The strut, which consist of two bars each of thickness 40 mm, is connected to the beam by a rivet passing through the three bars meeting at joint C. The allowable shear stress and bearing stress are t-60 MPa and o=120 MPa, respectively. a) Determine the required diameter of the rivet at the hinge C that carry safely by the given system. b) If the diameter rivet used on the support A is 20 mm check whether this rivet diameter is sufficient for the given system. 0.8m Im 0.6m 15 kN В Beam AD 20mm Strut CB 40mm 100mm 40mm 50mm 100mm Detail of joint C Detail of joint A
The frame supports the distributed load shown. Determine the state of stress acting at points E and D. Show the results on a differential element at this point. 4 kN/m DA -1.5m-15m+ 3 m 1 BA 20 mm 60 mm 20 mm. 5m T D 50 mm
len 9
Q.2 A force F is applied to a rigid beam AB. The diameter of the deformable 2х X post AC is 20 mm and diameter of the deformable post BD is 10 mm. A B F= 60 (kN) and x = 1.2 (m) E=70 GPa for the posts AC and BD. 1m 1m C Calculate the followings a) Normal stresses at post AC and BD b) Normal strains at post AC and BD c) Deformations at post AC and BD d) Angle of tilt that occurs in Beam AB.
Determine the variation in the width w as a function of x for the cantilevered beam that supports a concentrated force P at its end so that it has a maximum bending stress sallow throughout its length. The beam has aconstant thickness t.
9. A single horizontal force P of magnitude 900N is applied to end D of lever ABD shown in the figure below. Knowing that portion AB of the lever has a diameter 36mm, determine a) the normal and shearing stresses on an element located at point H and having sides parallel to the x and y axes, b) the principal planes and the principal stresses at point H. 300 mm 120 mm y B H A 540 mm 36 mm P D