Q.3 The mass of the trailer is 500 kg and that of the wheels alone might be neglected. The stiffness of the spring is 250 kN/m. Determine the range of the trailer travel velocity for which the steady state amplitude of vertical vibration is less than 25 mm ( ]X| < 25 mm). 50 mm 2Y 1.2 m

Q.3 The mass of the trailer is 500 kg and that of the wheels alone might be neglected. The stiffness of the spring is 250 kN/m. Determine the range of the trailer travel velocity for which the steady state amplitude of vertical vibration is less than 25 mm ( ]X| < 25 mm). 50 mm 2Y 1.2 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A block of mass 50 kg supported by a lining material made of rubber as shown in fig. When the block placed on the lining, the lining of static deflection is 10 mm. When the vibrator act with force F = 200sin50t N found the vibration amplitude is 2 mm. Determine i. the stiffness coefficient of the lining ii. The natural frequency i. the damping coefficient lining iv. the force exerted by the lining to the floor. vibrator 50 kg
s): A light rod is supported at each end by two similar springs, each of stiffness 850 N/m, and carries two concentrated masses, each of 1 kg, one at one end and one in the centre, as shown in Fig.2. Determine the two natural frequencies of vibration of the system. Purw 850 N/m 1 kg 850 N/m 1 kg Fig. 2
A factory machine with a mass of 320 kg vibrations up and down with frequency of 8 Hz. Amplitude of engine movement of 2 mm. Calculate the maximum acceleration of the machine, and what is the maximum Newtonian force obtained?
[6] An instrument panel weighing 30 lb is installed in a vehicle on a flexible mount that has an equivalent stiffness k = 400 lb/in and negligible damping. As a result of engine vibration, the vehicle vibrates with a steady-state amplitude of o.25 in at a frequency of 40 Hz. Determine the steady-state amplitude of vibration of the instrument panel.
An underdamped shock absorber is to be designed for a motor cycle of mass 200 kg(m). When the shock absorber is subjected to an initial vertical velocity due to a road bump, the resulting displacement-time curve is to be as indicated below. Find the necessary stiffness and damping constants of the shock absorber if the damped period of vibration is to be 10 sec(τd) and the amplitude x1is to be reduced to one-eighth in one half cycle. Example is attached
A 100 kg flow monitoring device is placed on a table in a laboratory. A pad of stiffness 2 x 105 N/m and damping ratio 0.051 is placed between the apparatus and the table. The table is bolted on the laboratory floor. Measurements indicate that the floor has a steady state vibration amplitude of 0.8 mm at a frequency of 50HZ. What is the amplitude of acceleration of the flow monitoring device? Select one: O 2 m/s? O 3 m/s? O 13.65 m/s2 3.9 m/s? TOSHIBA
Three (very small) beads with masses m, m, and u can slide without friction on a (very thin) fixed ring of radius a and are connected to each other by (weightless) springs of equal stiffness k and equilibrium length 1 = √3a. Find the normal frequencies and normal modes of vibration for this system. Interpret the physical meaning of the modes you have found. m wwwww. mu k,l wwww. k, I m
1) A 0.1 kg object oscillates as a simple harmonic motion along the x-axis with a frequencyf = 3.185 Hz. At a position x1, the object has a kinetic energy of 0.7 J and a potential energy 0.3 J. The amplitude of oscillation, A, is: (a) 0.12 m (b)0.22 m (c) 0.31 m (d)0.42 m
A rail road bumper is designed as a spring in parallel with a viscous damper. What is the bumper's damping coefficient such that the system has a damping ratio of 1.25, when the bumper is engaged by a rail car of 20,000 kg mass. The stiffness of the spring is 200 kN/m. If the rail car engages the bumper, while traveling at a speed of 20m/s, what is the maximum deflection of the bumper? poooo m
An electric motor of mass 25 kg is supported on a three-spring system. Thesprings are arranged in parallel, with the three stiffnesses being 10 kN/m,5 kN/m and 25 kN/m respectively. Viscous damping is present within the systemand has a magnitude of 0.4 kNs/m.i) Produce a sketch of the system and state its equation of motion.ii) Determine the damping ratio and comment on its value.iii) Determine the amplitude of vibration of the motor 5 cycles afterit is released from an initial displacement of 15 mm.
A vehicle is modelled as a combined mass-spring-damper system that oscillates in the vertical direction only. The driver of the vehicle travels along a road whose elevation varies sinusoidally as shown in Figure 2. The mass of the vehicle, which includes the driver, is 2500 kg. The stiffness and damping of the shocks are 40 kN/m and 3000 kg/s respectively. i. Determine the amplitude of vibration of the vehicle when it travels at a constant speed of 90 km/hr along the sinusoidal road. y/m 0.6 ►Velocity of vehicle m 0.4 ► Rigid massless tyre 0.2 distance (m) 20 60 80 -0.2 Figure 2
Three (very small) beads with masses m, m, and μ can slide without friction on a (very thin) fixed ring of radius a and are connected to each other by (weightless) springs of equal stiffness k and equilibrium length = √√3a. Find the normal frequencies and normal modes of vibration for this system. Interpret the physical meaning of the modes you have found. m .k,l www wwww m mu wwwww.. k,l