An electrical switch gear is supported by a crane through a steel cable of length 4 m and diameter 0.01 m. If the natural time period of the axial vibration of the switch gear is found to be o.01 s, find the stiffness of the switch cable. * O 4 MN/m O 5 MN/m 2 MN/m 3 MN/m

Q: mass of 10 kN s²/m is suspended from a spring whose spring constant 40 kN/m. The mass is subjected…

A: Given system,

Q: A 3 kg system is struck by a hammer blow that exerts 35 N for 0.15 seconds. The frequency response…

A:

Q: atural frequency in Hertz of an undamped mass-spring system with a m= 100 grams and k= 100 N/m

A: Given:m=100 grams =0.1 kgk=100 N/m

Q: A spring mass system consists of a mass 10 kg and a spring with a stiffness of 2 kN/m. The spring…

A:

Q: A damped single-degree-of-freedom vibration system has m= 7 kg, c= 549 Ns/m, and k= 10 kN/m.…

A: In vibrating system, damping ratio represents the degree of dampness provided in the vibrating…

Q: In a damped single-degree-of-freedom system with a mass of m = 10 kg, stiffness coefficient k = 4000…

A:

Q: Please solve this problem by showing the manual calculation and choose the correct answer(SUBJECT:…

A: Given: →m1=1.8 Kg ; →m2=0.7Kg→k1=250 N/m→k2=700 N/m→k3=100 N/m And the give vibration is free…

Q: Consider the following system (m 27 kg and k=3kN/m). in k Suppose that the damping coefficient is…

A: Given , morning =27kg and K = 3000 N/m  C = 0.5 *C_c

Q: 200 mm m 15 kg C-40 N-5/m TTTTT Fig. 1 K-300 N/m 100 mm

A: Mass =15kgC= 40 N-s/mK= 300 N/m

Q: A simple-simply supported beam subjected to a uniformly distributed harmonically varying load;…

A:

Q: A damped single-degree-of-freedom vibration system has m= 7 kg, c= 589 Ns/m, and k= 8 kN/m.…

A:

Q: The phase angle describe the relative shift in the sinusoidal vibration of the spring mass system…

A: given; ϕ=phase anglex0=initial displacementx(t)=ω2x02+v02ω*sin(ωt+ϕ)and;ϕ=tan-1ωx0v0

Q: DETERMINE THE AMPLITUDE OF THE STEADY STATE VIBRATION AND ANGLE BY WHICH X LAGS Y.

A:

Q: The structure shown in figure has a mass of 100 kg and a translational stiffness of 40,000 N/m. It…

A: Mass M= 100 kg   Stiffness k= 40,000 N/m Amplitude P0=F0= 500N excitation frequency ω =15 rad/s…

Q: A simple seismometer used to measure ground motion is shown in the figure below. If the mass m = 300…

A: Given: The mass m=300 kg Stiffness k=3000 Nm Damper c=600 Nm The ratio of output to input amplitude…

Q: As shown in figure a mass of 100 kg is held between two springs. The natural frequency of vibration…

A: Given:m=100 kgspring stiffness, k=20 kN/mFind,Natural frequency of system?

Q: A mass of 21.5 kg is vibrating freely at the end of 3 springs connected in parallel. The spring…

A:

Q: Consider a spring-damper vibration isolation system for a microscope of mass M (shown). harmonic…

A: As there is no any isolation so by decreasing the eccentricity transmitted force get reduced

Q: Find the natural frequency (in Hertz) of the system illustrated in the following figure. Consider…

A:

Q: A damped single-degree-of-freedom vibration system has m= 3.6 kg , c= 513 Ns/m , and k= 24 kN/m .…

A: m = 3.6 kg c = 513 Ns/m k = 24 kN/m = 24000 N/m

Q: please answer ans explain

A: Step 1:1. Transfer Functions: Due to the complexity of deriving transfer functions for a…

Q: As shown in figure a mass of 100 kg is held between two springs. The natural frequency of vibration…

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.