Q.3: Compute the available strength of a built-up compression member with a length 16 ft,as shown in following Figure. The ends are Fixed. The outside flange is PL3/4 in.x5 in., the inside flange is PL3/4x8 in., and the web is PL3/8in.×10 ½ in. The material is ASTM A572 Grade 55. b=8" inside flange Pu tw =%" 16 b=5 outside flange h=10% 12

Q.3: Compute the available strength of a built-up compression member with a length 16 ft,as shown in following Figure. The ends are Fixed. The outside flange is PL3/4 in.x5 in., the inside flange is PL3/4x8 in., and the web is PL3/8in.×10 ½ in. The material is ASTM A572 Grade 55. b=8" inside flange Pu tw =%" 16 b=5 outside flange h=10% 12

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Y1
For the Beam section below, check if steel yields and determine the ACI design flexural strength. 12 in. 15 in. 4 #10 bars $3 in. f, = 60,000 psi f;= 4000 psi -18 in.-
Consider the truss shown in (Egure 1). Suppose that F-60 kN and F₂-25 kN Figure 40 KN Part C Fau 50 AN Submit -2m- D 15m 1of1 > 15m 15m μA Value -F₂ Part A Request Answer Determine the force in member ED of the truss, and state if the member is in tension or compression Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. HA FED Value Submit Part B Request A Determine the force in member EH of the truss, and state if the member is in tension or compression Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Submit Fon- Value Determine the force in member GH of the truss, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of…
PLEASE ANSWER ASAP
PLS ANSWER ASAP THANKS!
Calcualte the following: Total factored floor load in 2 decimal places, ___ kPa Total factored uniform load on girder GH in 2 decimal places, ___ kN/m Maximum ultimate bending moment at discontinuous end of girder JK to the nearest whole number = ___ kN·m
A rectangular tied braced column is reinforced with 6-28mm bars as shown in the figure below. Check the adequacy of the column for the following gravity loads: - - - - - - Service dead load = 1050kN Service live load = 850 kN Service dead load moment = 39 kN-m Service live load moment = 27 kN-m top=bott. = 1.0 40 lu = 5.0m f = 27.6 N/mm², fy = 414 N/mm² axis of bending 500mm Ties 10mm@300c/c } 350mm At eccentricity of 40mm P M +40 + 500mm MU +40- P Top end Bott. end
Q2) The members of the truss structure shown below is plain concrete. The compressive strength of the concrete is 25 MPa. Compute the maximum load P that can be carried by the structure. (Cross section of each member of the truss is 200 x 200 mm and don't use material factors and do not consider slenderness) Comment on your results briefly. P A& 2m SC 2 m 1380 2m D
Determine the maximum load that an 8 foot long 2"x4" rectangular aluminum alloy bar (E = 10.5x10^3ksi, σY = 40 ksi) can support with a factor of safety of 3 for both crushing and buckling if it has endconditions of:a. Pinned-pinned.b. Pinned-fixed.c. Fixed-free.d. Fixed-fixed.
Determine the force of the members for the space truss shown in the figure. Joints A and B are supported by ball-and-socket while Joint C is supported by short link along z-axis. Indicate whether member is tension (T) or compression (C). 2m y Sm Az By BX Bz PAR Ax CSXScanned with Ca canner a SISU KN 15m 1 2117
A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 8 m long, pinned at the top fixed at bottom with additional lateral support at mid height in the weak direction. The properties are as follows: Ag = 14,500 sq.mm, Ix= 258.6 x10^6 mm ^4 Iy=84.375 x 10^6 mm^4. 55. calculate the critical slenderness ratio with buckling about strong axis.
2) Find the axial stresses of menbers FD, GD, GE State if it is tensile or Compressive. 4M 3M A LE 3m G 20 RN Go KN